Skip to main content

2010 Cadillac Truck Escalade RWD V8-6.2L Technical Service Bulletin # 08-09-41-005B Date: 110406

2010 Cadillac Truck Escalade RWD V8-6.2L Technical Service Bulletin # 08-09-41-005B Date: 110406

Interior - Passenger Air Bag Is Not Flush With Dash

TECHNICAL

Bulletin No.: 08-09-41-005B

Date: April 06, 2011

2010 Cadillac Truck Escalade RWD V8-6.2L Page 196

Subject: Passenger Side Air Bag Door Not Flush with Dash Pad/Warped (Reposition Locking Tabs on Air Bag Panel)

Models:

2007-2012 Cadillac Escalade, Escalade ESV, Escalade EXT

2007-2012 Chevrolet Avalanche, Silverado, Suburban, Tahoe

2007-2012 GMC Sierra, Yukon, Yukon XL, Yukon Denali, Yukon Denali XL

Supercede:

This bulletin is being revised to update the model years. Please discard Corporate Bulletin Number 08-09-41-005A (Section 09 - Restraints).

Condition

Some customers may comment that the air bag door does not sit flush with the instrument panel (dash pad) or that the door appears warped.

Cause

This condition may be caused by a trim locking tab that is not fully engaged in the mounting bracket.

Correction

Reposition the trim locking tabs on the air bag panel following the procedure below.

Important

This repair is for appearance reasons only and has no effect on the operation or performance of the air bag.

1. Disable the SIR system. Refer to Inflatable Restraint Instrument Panel Module Replacement for Disabling and Enabling the SIR system.

2. The locking tab will be bent upward. Using a plastic trim stick, gently move the panel up to expose the deformed locking tab.

3. Straighten the locking tab using the plastic trim stick.

4. Press down on the air bag panel to seat it in the correct position.

2010 Cadillac Truck Escalade RWD V8-6.2L Page 197

5. Enable the SIR system. Refer to Inflatable Restraint Instrument Panel Module Replacement for Disabling and Enabling the SIR system.

Warranty Information

For vehicles repaired under warranty, use the table.

Comments

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138, Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...