Skip to main content

2010 Cadillac Truck Escalade RWD V8-6.2L Technical Service Bulletin # 06-08-64-035G Date: 100601

2010 Cadillac Truck Escalade RWD V8-6.2L Technical Service Bulletin # 06-08-64-035G Date: 100601

Body - Squeak/Itching Noise in Upper Door Area

TECHNICAL

Bulletin No.: 06-08-64-035G

Date: June 01, 2010

Subject: Squeak/Itching Noise in Upper Door Area (Replace Weatherstrip Assembly)

Models:

2007-2010 Cadillac Escalade, Escalade ESV, Escalade EXT

2007-2010 Chevrolet Avalanche, Silverado, Suburban, Tahoe

2007-2010 GMC Sierra, Yukon, Yukon XL, Yukon Denali, Yukon Denali XL

Supercede:

This bulletin is being revised to update parts description information. Please discard Corporate Bulletin Number 06-08-64-035F (Section 08 - Body

and Accessories).

Condition

Some customers may comment on a squeaking or itching noise in the upper door area when driving.

2010 Cadillac Truck Escalade RWD V8-6.2L Page 305

Cause

This condition may be caused by the roof drip weatherstrip to door frame contact. This could occur at any or all of the doors.

Correction

Replace the weatherstrip assembly. Refer to Door Opening Weatherstrip Replacement in SI.

Parts Information

Warranty Information

For vehicles repaired under warranty, use the appropriate labor operation from the Labor Time Guide.

Comments

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138, Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...