Skip to main content

2010 Cadillac Truck Escalade RWD V8-6.2L Technical Service Bulletin # 09-01-38-004 Date: 090731

2010 Cadillac Truck Escalade RWD V8-6.2L Technical Service Bulletin # 09-01-38-004 Date: 090731

A/C - A/C Indicator Or Recirculation Indicator Flashing

INFORMATION

Bulletin No.: 09-01-38-004

Date: July 31, 2009

Subject: Information on Vehicles with HVAC Control Module A/C and Recirculation Indicators Flashing

Models:

2008-2010 Buick Enclave

2007-2010 Cadillac Escalade Models

2007-2010 Chevrolet Avalanche, Silverado, Suburban, Tahoe

2009-2010 Chevrolet Traverse

2007-2010 GMC Acadia, Sierra, Yukon, Yukon XL

2007-2010 Saturn OUTLOOK

2010 Cadillac Truck Escalade RWD V8-6.2L Page 244

Condition/Concern

Important

DO NOT replace the HVAC Control Module for a flashing A/C Indicator or flashing Recirculation Indicator, as this is normal operation.

Some customers may comment on any of the following conditions:

- The Air Conditioning (A/C) indicator on the heating ventilation and air conditioning (HVAC) control module flashes then turns OFF after

they press the A/C button.

- The Recirculation indicator on the HVAC control module flashes then turns OFF after they press the Recirculation button.

- The passenger (PASS) temperature setting flashes then turns OFF after they press the PASS button.

- The driver and passenger temperature settings revert to previous temperature settings when changing from defrost to bi-level, vent, floor or

defog.

This is normal operation for the HVAC Control Module and indicates that the A/C, Recirculation and Passenger functions are not available at this

time.

The following parameters are reasons that the A/C functions may not be available (calibrated values vary by program):

- Ambient air temperature (AAT) is too cold (if equipped with Ambient Air Temperature Sensor)

- Vehicle system voltage is less than 9.5 volts

- Refrigerant pressure is too low

- Refrigerant pressure is too high

- Engine coolant temperature (ECT) is too high

- Engine is not in RUN

- HVAC Control Head is in the OFF position

The following mode settings are reasons Recirculation may not be available:

- Mode switch set on Floor

- Mode switch set on Defog

- Mode switch set on Defrost

The following mode setting is the reason the passenger mode may not be available:

The mode switch is set on Defrost.

Note

The reason(s) A/C is currently disabled can be viewed with a Tech 2(R) by navigating to HVAC Data display and viewing the A/C Permission

parameter.

Recommendation/Instructions

Note

To maintain the highest level of customer satisfaction, INFORM the customer of all of the following conditions:

- The flashing A/C indicators on the HVAC control module represent normal operation and indicate that the A/C, Recirculation and/or

Passenger functions are not available at this time.

- Changing the passenger temperature setting while in the Defrost mode will change the Driver temperature setting.

- Changes made to temperature settings while in Defrost mode will revert to the previous settings upon returning to Bi-level, Vent, Floor or

Defog.

Consult the appropriate vehicle Service Information (SI) for a detailed HVAC Description and Operation.

Comments

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138, Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...