Skip to main content

2010 Cadillac Truck Escalade RWD V8-6.2L Technical Service Bulletin # 10-06-01-007D Date: 120410

2010 Cadillac Truck Escalade RWD V8-6.2L Technical Service Bulletin # 10-06-01-007D Date: 120410

Engine - Valve Lifter Tick Noise At Start Up

TECHNICAL

Bulletin No.: 10-06-01-007D

Date: April 10, 2012

Subject: Active Fuel Management (AFM) Engine, Valve Lifter Tick Noise at Start Up When Engine Has Been Off for 2 Hours or More (Evaluate

Noise and/or Replace AFM Valve Lifters)

Models:

2007 Buick Rainier

2009 Buick LaCrosse Super, Allure Super (Canada Only)

2007 Cadillac Escalade

Built Prior to April 1, 2006 with 6.2L Engine RPO L92 (These engines were built with AFM Hardware but the AFM system was disabled)

2010-2011 Cadillac Escalade, Escalade ESV, Escalade EXT

2007 Chevrolet Monte Carlo

2007-2009 Chevrolet Impala

2007-2011 Chevrolet Avalanche, Silverado, Suburban, Tahoe, TrailBlazer, TrailBlazer EXT

2010-2011 Chevrolet Camaro SS

2007-2011 GMC Envoy, Envoy XL, Sierra, Yukon, Yukon Denali, Yukon XL, Yukon XL Denali

2007-2008 Pontiac Grand Prix

2008-2009 Pontiac G8

2007-2009 Saab 9-7X

Equipped with AFM (Active Fuel Management) and V8 Engine RPO L76, L94, L99, LC9, LFA, LH6, LMG, LS4, LY5 or LZ1

Attention:

This bulletin only applies to the AFM V8 engines listed above. It DOES NOT apply to non-AFM Engines. If you are dealing with a non-AFM

engine that is experiencing a similar noise, refer to Engine Mechanical > Diagnostic Information and Procedures > Symptoms in SI.

Supercede:

This bulletin is being revised to update the Correction information by removing the non-AFM valve lifter replacement and removing the non-AFM

valve lifter Parts Information. Please discard Corporate Bulletin Number 10-06-01-007C (Section 06 - Engine/Propulsion System).

Condition

Some customers may comment on an engine valve lifter tick noise that occurs after the engine has been shut off for at least two hours. The tick

noise may last from two seconds to ten minutes.

Cause

This condition may be caused by any of the following:

- Aerated oil in the valve lifter body, resulting in the valve lifter being unable to purge the air quickly.

2010 Cadillac Truck Escalade RWD V8-6.2L Page 85

- A low engine oil level or incorrect oil viscosity.

- Dirty or contaminated oil.

- A low internal valve lifter oil reservoir level.

- Debris in the valve lifter.

- A high valve lifter leak down rate.

Correction

If the SI diagnostics do not isolate the cause of this valve lifter tick noise and normal oil pressure is noted during the concern, perform the following

steps:

1. Inspect the engine oil condition and level. Refer to Owner Manual > Service and Appearance Care > Checking Things Under the Hood >

Description and Operation > Engine Oil in SI.

瀚慖f the engine oil is more than one quart low, an incorrect oil viscosity is being used or if poor quality/contamination is observed, change

the oil and filter.

Notice

Allow at least a two hour soak time between engine OFF and start up when evaluating the valve lifter tick noise.

2. Start the engine and evaluate the valve lifter tick noise.

瀚慖f the valve lifter tick noise is still present, replace all 8 active fuel management (AFM) valve lifters ONLY.

Refer to Valve Lifter Replacement (With AFM) in SI.

Parts Information

Warranty Information (excluding Saab Models)

For vehicles repaired under warranty, use:

Warranty Information (Saab Models)

For vehicles repaired under warranty, use the table.

Comments

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138, Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...