Skip to main content

2000 Porsche Boxster (986) F6-2.7L Page 84

Literature

Technical Service Bulletin # 99/04 Date: 040922

Antitheft - Aftermarket System Installation Warning

Boxster

9/04 9668

9/21/04

Binder - 9, Electrical

Installation of After Market Theft Prevention Systems

Vehicle Type:

Boxster/Boxster S

Model Year:

As of '97 (V)

Concerns:

Installing additional anti-theft protection (anti-car jacking systems) can cause malfunctions in the vehicle electrical/electronic system.

Information:

After market anti-car jacking systems are electrical/electronic equipment in the vehicle which expand the existing theft protection of the vehicle and

also support and facilitate the location of a stolen vehicle. Typically, the stolen vehicle is located via GPS/GSM or radar.

Malfunctions:

Investigations based on complaints have shown that after installing such a system, the following malfunctions can occur in the vehicle

electrical/electronic system:

- remote control does not function,

- interference in or poor radio reception,

- increased current draw,

- incorrect triggering of the theft warning system (vehicles with I No. 534 or 535).

In some countries, additional anti-theft protection (anti-car jacking systems) must be installed for insurance/technical reasons. These systems are

not approved by Porsche.

Measures:

Installing additional anti-theft protection (anti-car jacking system).

If the customer would like to have such a system installed, the customer should be informed about the possible, above-mentioned known-to-date

malfunctions. Due to the increased current draw, it is recommended that the customer use the Porsche battery maintainer.

Repairs on vehicles with additional anti-theft protection (anti-car jacking system).

If there are customer complaints regarding the above-mentioned malfunctions, the customer should be asked if such a system is installed in the

vehicle. Repair work relating to such systems cannot be claimed under warranty.

Please inform your sales and parts department personnel accordingly.

Comments

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138, Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...