12.4.4Join the leads in the wire-end ferrule using a pair of crimping pliers (Fig. 13, Item A).
12.4.5Solder the tips of the projecting ends of the leads (Item B).
12.4.6Insulate the soldered joint with 4 x 35 shrink tubing.
Caution!
Damage to the interior and the leads from the heating effect of the heat gun!
> Observe the blower outlet direction of the heat gun during the shrinking procedure.
> Close the open end of the shrink tubing using a pair of flat-nosed pliers (Item C).
12.4.7Snap the contact spring into the housing socket again.
12.4.8Use electrical tape to secure the lead to the wiring harness in the area of the shrink tubing.
12.5 Follow the same procedure for work on the other leads/contact springs. Trim the wires in such a way that the connection points are
offset with respect to each other.
12.6 Reassemble the plug in reverse order. When doing so, replace the previous plug cap (See Figure 10, Item A) with the plug cap
contained in the service set.
Caution!
Airbag warning light lights up if tie-wrap is insufficiently fastened.
> Bundle all leads on the vehicle-side plug on the plug cap using a tie-wrap (Figure 14).
12.7 Bundle the seat ground lead again. Add more banding if necessary.
13. Replace belt buckle.
A new belt buckle with gold-plated contact pins must be installed. A strain relief element for the belt buckle wiring harness is intended on the
seat-side plug.
13.1 Remove the previous belt buckle; see Boxster Technical Manual, Group 6, Repairs, 69 24 19 - Removing and installing the front belt
buckle.
13.2 Install the new belt buckle.
Distinguishing the belt buckles:
The belt buckles can be recognized by way of thee stamped number and by the plug color.
Driver's seat - 996.803.183.09, blue plug
Passenger's seat - 996.803.183.10, green plug.
Caution!
Airbag warning light lights up if tie-wrap is insufficiently fastened.
12.4.5Solder the tips of the projecting ends of the leads (Item B).
12.4.6Insulate the soldered joint with 4 x 35 shrink tubing.
Caution!
Damage to the interior and the leads from the heating effect of the heat gun!
> Observe the blower outlet direction of the heat gun during the shrinking procedure.
> Close the open end of the shrink tubing using a pair of flat-nosed pliers (Item C).
12.4.7Snap the contact spring into the housing socket again.
12.4.8Use electrical tape to secure the lead to the wiring harness in the area of the shrink tubing.
12.5 Follow the same procedure for work on the other leads/contact springs. Trim the wires in such a way that the connection points are
offset with respect to each other.
12.6 Reassemble the plug in reverse order. When doing so, replace the previous plug cap (See Figure 10, Item A) with the plug cap
contained in the service set.
Caution!
Airbag warning light lights up if tie-wrap is insufficiently fastened.
> Bundle all leads on the vehicle-side plug on the plug cap using a tie-wrap (Figure 14).
12.7 Bundle the seat ground lead again. Add more banding if necessary.
13. Replace belt buckle.
A new belt buckle with gold-plated contact pins must be installed. A strain relief element for the belt buckle wiring harness is intended on the
seat-side plug.
13.1 Remove the previous belt buckle; see Boxster Technical Manual, Group 6, Repairs, 69 24 19 - Removing and installing the front belt
buckle.
13.2 Install the new belt buckle.
Distinguishing the belt buckles:
The belt buckles can be recognized by way of thee stamped number and by the plug color.
Driver's seat - 996.803.183.09, blue plug
Passenger's seat - 996.803.183.10, green plug.
Caution!
Airbag warning light lights up if tie-wrap is insufficiently fastened.
Comments
Post a Comment