Skip to main content

2010 Cadillac Truck Escalade RWD V8-6.2L Page 2317

2010 Cadillac Truck Escalade RWD V8-6.2L Page 2317

2. Test for 6.5-7.0K ohm between the signal terminal 3 and the B+ terminal 4 with the switch in the released position.

瀚慖f not the specified value, replace the S2 transmission manual shift switch.

3. Test for 1.5-2.0K ohm between the signal terminal 3 and the B+ terminal 4 with the switch in the plus position.

瀚慖f greater than the specified range, replace the S2 transmission manual shift switch.

4. Test for 3.8-4.0K ohm between the signal terminal 3 and the B+ terminal 4 with the switch in the minus position.

瀚慖f greater than the specified range, replace the S2 transmission manual shift switch.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Shift Lever Replacement (See: Steering and Suspension/Steering/Steering Column/Service and Repair/Shift Lever Replacement) for

automatic transmission manual shift switch replacement.

* Control Module References (See: Testing and Inspection/Programming and Relearning) for body control module replacement, setup, and

programming.

6L45/6L50/6L80/6L90 - Automatic Transmission

DTC P0815, P0816, P0826, or P1876

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0815

- Upshift Switch Circuit

DTC P0816

- Downshift Switch Circuit

DTC P0826

- Up and Down Shift Switch Circuit

DTC P1876

- Up and Down Shift Enable Switch Circuit Low Voltage

Diagnostic Fault Information

Circuit/System Description

The driver shift request (DSR), also known as the TAP Up/Downshift manual shift function, allows the driver to select the desired range of gears

for current driving conditions. The DSR shift system is activated when the gear selector is in the manual position. The DSR system is deactivated in

all other range positions. Pressing the plus (+) switch once will command the body control module (BCM) to signal the transmission control

module (TCM) to upshift to the next high gear. Pressing the minus (-) switch once will command the BCM to signal the TCM to downshift to the

next lowest or previous gear. The TCM will not allow a downshift if the transmission is compromised by over-speeding. The automatic

transmission manual shift switch is comprised of three different resistors values in series and two switches. The BCM supplies a 12 volt circuit to

the automatic transmission manual shift switch. The signal circuit varies the voltage back to the body control module depending on which switch is

depressed.

Conditions for Running the DTC

Comments

Post a Comment

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...
Read more

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...
Post a Comment
Read more

D138， Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...
Post a Comment
Read more