Skip to main content

2010 Cadillac Truck Escalade RWD V8-6.2L Page 2582

2010 Cadillac Truck Escalade RWD V8-6.2L Page 2582

Typical Scan Tool Data

Circuit/System Description

The clutch pressure control (PC) solenoid 5 is part of the control solenoid valve assembly which has no serviceable parts. The normally low PC

solenoid 5 regulates and directs oil pressure to the 1-2-3-4 clutch regulator valve and 1-2-3-4 clutch boost valve. Increasing PC solenoid 5 pressure

increases pressure to the 1-2-3-4 clutch. The TCM varies the current to the PC solenoid 5 through a low side driver. Increasing the current to PC

solenoid 5 increases oil pressure by closing OFF the solenoid exhaust port. Decreasing the current to PC solenoid 5 decreases oil pressure by

opening the exhaust port. PC solenoid 5 power is supplied by the TCM through a high side driver (HSD). The HSD protects the circuit and

components from excessive current flow. If excessive current flow is detected, the HSD will turn OFF. When the fault is corrected, the HSD will

reset.

Conditions for Running the DTC

P2728, P2729, or P2730

* DTCs P2728, P2729, or P2730 have not set this ignition.

* The ignition voltage is 8.6 volts or greater.

* The engine speed is 400 RPM or greater for 5 seconds.

* The clutch PC solenoid 5 is commanded ON.

Conditions for Setting the DTC

P2728

The TCM detects an internal electrical performance malfunction of the clutch PC solenoid 5 control circuit where the measured clutch PC solenoid

5 current does not equal the commanded clutch PC solenoid 5 current for 5 seconds.

P2729

The TCM detects a short to ground on the clutch PC solenoid 5 control circuit for 1 second.

P2730

The TCM detects an open or short to voltage on the clutch PC solenoid 5 control circuit for 1 second.

Action Taken When the DTC Sets

P2728

* DTC P2728 is a Type C DTC.

* The TCM freezes transmission adaptive functions.

P2729

* DTC P2729 is a Type A DTC.

* The transmission defaults to 2nd gear or reverse gear.

* The TCM forces TCC OFF.

* The TCM freezes transmission adaptive functions.

* The TCM commands maximum line pressure.

* The TCM enables Torque management.

* The TCM inhibits TAP Up/Down function.

Comments

Post a Comment

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...
Read more

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...
Post a Comment
Read more

D138， Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...
Post a Comment
Read more