Skip to main content

Mercedes Benz Truck G 55K AMG Mercedes2020-2010 Benz Truck G 55K AMG Technical Service Bulletin # S-54_65-252 Date: 120207

Mercedes Benz Truck G 55K AMG Mercedes2020-2010 Benz Truck G 55K AMG Technical Service Bulletin # S-54_65-252 Date: 120207



Parking Assist - Malfunction and Fault Scenarios



Date: February 7, 2012



Order No.: S-B-54.65/252



Group: 54



SUBJECT:



MY-All, Models 163, 164, 166, 170, 171, 172, 197, 202, 203, 204, 207, 208, 209, 210, 211, 212, 215, 216, 218, 219, 220, 221, 230, 231, 240, 245,



251, 463 with Code 220 Parktronic system (PTS); Code 230 Advanced Parking Guidance; Code 235 Active Park Assist



2010 Mercedes Benz Truck G 55K AMG (463.271) V8-5.5L SC (113.993) 30



Parktronic Malfunctions and Faults



This is an overview of Parktronic malfunction and fault scenarios, respectively.



Malfunction Scenario 1



Malfunctions are indicated with double red (4 LEDs) warning elements and no warning tone (Figure 1).



An entry is not saved in fault memory.



Malfunctions can be triggered by external ultrasonic signals:



^ Compressed air



^ Drier blower for a washer system



^ Rail vehicles



^ Brake squeal on vehicle or a nearby vehicle



Or through:



^ Soiling of sensors with ice or snow



^ License plate brackets



Fault Scenario 2



Faults are indicated in the Parktronic warning elements with double red (4 LEDs) with warning tone (Figure 1) (see arrows).



An entry is saved in fault memory.



The sensor function is automatically checked while driving at between 22-37 mph. If a fault occurs when driving, then this is issued at a speed less



than 9 mph with double red lights and warning tone.



The following applies to both scenarios:



If a malfunction or a fault is present for more than 2 seconds, the display in the warning elements goes out and the PARKTRONIC OFF button in



the UCP lights up in red.



Diagnosis



2010 Mercedes Benz Truck G 55K AMG (463.271) V8-5.5L SC (113.993) 31



To fix issues that cannot be clearly located via fault codes in fault memory, check for correct and central installation (Figure 3) (C) or for any



damage caused by stone chipping (Figure 2) (A) (B).



The decoupling ring must be centered and custom fit when installed (Figure 3) (C) and Figure 4 (C). Refer also to S-B-54.651251 Parktronic

Comments

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138, Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...