Skip to main content

2020 -2010 Mercedes Benz Truck G 550 Technical Service Bulletin # LI82-85_P-048914 Date: 100218

2020 -2010 Mercedes Benz Truck G 550 Technical Service Bulletin # LI82-85_P-048914 Date: 100218



COMAND(R) - 'Drive Unavailable, Temp. Too High' Message



COMAND APS: Fault message "Drive unavailable, temperature too low or too high"



Topic number LI82.85-P-048914



Version 1



Design group 82.85 Navigation and communication systems (CNS, ICS, COMAND, FleetBoard)



Date 02-18-2010



Validity Model 171, 230, 164, 251, 169, 245, 211, 219, 203.7 with COMAND (code 512 or 527) and code 809 or 800 (NTG2.5)



Model 463 with SA code EU1



Reason for change



Reason for block



Complaint:



2010 Mercedes Benz Truck G 550 (463.236) V8-5.5L (273.963) 177



Complaint 1:



At high altitudes (over approx. 3000 meters above sea-level) the navigation main menu sporadically displays the fault message "Drive unavailable,



temperature too high".



The following functions are restricted due to the shutdown of the hard drive.



- Navigation



- Voice control



- Address book



- Music register (downloaded music onto the head unit hard-drive)



- Gracenote database for identifying album, track and performer information on an audio CD



Complaint 2:



The navigation main menu permanently displays the fault message "Drive unavailable, temperature too low or too



high"



Cause:



Re 1.)



The hard drive shuts down at high altitudes (over approx. 3000 m) and when the temperature of the hard drive is high.



a) At low altitudes the message disappears and the COMAND unit (A40/3) operates without problems. This is due to a safety feature created to



protect the hard-drive from permanent damage.



b) High hard drive temperatures are increased by high volume settings especially in vehicles without sound system (SA code 810), high outside



and engine temperatures and unfavorable settings on the heating/air conditioning. With the altitude increase and decreasing of air around



hard-drive assembly, the HDD starts the shut down process as the surrounding head unit temperature also reaches around 55 degrees Celsius.



The head unit is working as specified in this use case.



Re. 2.)



There is a hardware fault in the COMAND unit (A40/3).



Remedy:



Remedy 1.)



To prevent damage to the hard drive, it is shut down at high altitudes and high temperatures. This is due to a safety feature (series production



configuration). => Do not replace any equipment!



Remedy 2.)



If the fault occurs constantly, replace the COMAND APS (A40/3). Refer to EPC.



Note:



If the vehicle is fitted with a COMAND APS (A40/3) with PIN theft protection, the PIN code must be recorded in the VeDoc system. Pay attention



to the relevant information during initial startup with DAS / Xentry Diagnostics.



2010 Mercedes Benz Truck G 550 (463.236) V8-5.5L (273.963) 178

Comments

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138, Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...