Skip to main content

2010 Cadillac Truck Escalade RWD V8-6.2L Page 1128

2010 Cadillac Truck Escalade RWD V8-6.2L Page 1128

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC P0A2B

- Drive Motor 1 Temperature Sensor Performance

DTC P0A2C

- Drive Motor 1 Temperature Sensor Circuit Low Voltage

DTC P0A2D

- Drive Motor 1 Temperature Sensor Circuit High Voltage

DTC P0A31

- Drive Motor 2 Temperature Sensor Performance

DTC P0A32

- Drive Motor 2 Temperature Sensor Circuit Low Voltage

DTC P0A33

- Drive Motor 2 Temperature Sensor Circuit High Voltage

Diagnostic Fault Information

Typical Scan Tool Data

Circuit/System Description

The motor temperature sensor (MTS) is a non-serviceable part of the drive motor generator assembly. The MTS sensor is a thermistor, or a resistor

that changes value when the temperature changes. The sensor has a negative-temperature coefficient. This means that as the temperature increases,

the resistance decreases, and as the temperature decreases, the resistance increases. The motor control module (MCM) supplies about a 5-volt

reference signal to the sensor and measures the voltage drop in the circuit. When the motor is cold, the sensor resistance is high and the MCM

detects high signal voltage. As the motor temperature increases, the resistance of the sensor decreases, which lowers the signal voltage.

Conditions for Running the DTC

P0A2B and P0A31

* DTCs P0A2C, P0A2D, P0AEF, P0AF0, P0BD3, P0BD4, P0BDD, P0BDE are not set.

* Ignition ON after the engine has been OFF for at least 6 hours.

* Average of phase U, V, W inverter temperatures is greater than -12掳C (+10掳F).

* Motor temperature is greater than -40掳C (-40掳F).

P0A2C, P0A2D, P0A32 and P0A33

The ignition is ON.

Conditions for Setting the DTC

P0A2B and P0A31

* The average of the three motor phase sensor temperatures and the motor temperature are not within 28掳C (50掳F) of each other at ignition ON.

* The DTC sets within 3 seconds when the above condition is met.

P0A2C and P0A32

* Motor temperature sensor signal is less than 0.29V.

* The DTC sets within 3 seconds when the above condition is met.

Comments

Post a Comment

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...
Read more

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...
Post a Comment
Read more

D138， Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...
Post a Comment
Read more