2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2953

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2953

* Component Connector End Views (See: Diagrams/Connector Views)

* Inline Harness Connector End Views (See: Power and Ground Distribution/Multiple Junction Connector/Diagrams)

Description and Operation

* Transmission General Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and

Operation/6L45/6L50/6L80/6L90 - Automatic Transmission/Transmission General Description)

* Transmission Component and System Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and

Operation/6L45/6L50/6L80/6L90 - Automatic Transmission/Transmission Component and System Description)

* Electronic Component Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and

Operation/6L45/6L50/6L80/6L90 - Automatic Transmission/Electronic Component Description)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Special Tools

DT-47825-10 - Jumper Harness

Circuit/System Verification

1. Operate the vehicle in 2nd gear long enough to ensure at least a 3掳C (5掳F) rise in TCM temperature.

2. Operate the vehicle in drive range and ensure TCC is commanded ON for 1 minute. Verify with a scan tool the following test status

parameters display OK:

* TCC Pressure Control Solenoid Valve Performance Test Status

* TCC Pressure Control Solenoid Valve Control Circuit High Voltage Test Status

* TCC Pressure Control Solenoid Valve Control Circuit Low Voltage Test Status

3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

Note: You must perform the Circuit/System Verification first.

1. Ignition OFF, remove the Q8 control solenoid valve assembly. Refer to Control Solenoid Valve and Transmission Control Module Assembly

Replacement (See: Powertrain Management/Transmission Control Systems/Actuators and Solenoids - Transmission and

Drivetrain/Actuators and Solenoids - A/T/Shift Solenoid/Service and Repair).

2. Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and Drivetrain/Automatic

Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/6L45/6L50/6L80/6L90 - Automatic

Transmission/Control Solenoid Valve and Transmission Control Module Assembly Inspection).

3. Place the Q8 control solenoid valve assembly on a clean work surface near the transmission assembly.

4. Connect DT-47825-10 - jumper harness between the vehicle wire harness electrical connector, and the Q8 control solenoid valve assembly

electrical connector.

5. Ignition ON, verify with a scan tool the following test status parameters display OK:

* TCC Pressure Control Solenoid Valve Performance Test Status

* TCC Pressure Control Solenoid Valve Control Circuit High Voltage Test Status

* TCC Pressure Control Solenoid Valve Control Circuit Low Voltage Test Status

瀚慖f any test status parameter displays Fault or Malfunction, replace the Q8 control solenoid valve assembly.