Monday, February 17, 2020

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1054

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1054



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit



Testing/Circuit Testing)



* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic



Procedures/Connector Repairs/Connector Repairs)



* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General



Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)



* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring



Repairs/Wiring Repairs)



DTC Type Reference



Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code



(DTC) Type Definitions)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Special Tools



J 35616 Connector Test Adapter Kit



Circuit/System Verification



1. Engine idling, DTC P0111, P0112, P0113, or P0114 should not set.



2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the



conditions that you observed from the Freeze Frame/Failure Records data.



Circuit/System Testing



1. Ignition OFF, disconnect the harness connector at the B65 Intake Manifold Pressure and Air Temperature sensor.



2. Remove the fuse that supplies B+ to terminal 56 X2 of the ECM.



Caution: Do NOT use a test lamp to test the continuity of the circuit. Damage to the control module may occur due to excessive current



draw.



3. Ignition OFF and all vehicle systems OFF. It may take up to 2 minutes for all vehicle systems to power down. Test for less than 5 ohm



between the low reference circuit terminal 1 and ground.



瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance, or for a short to voltage. If the



circuit/connections test normal, replace the K20 ECM.



4. Install fuse that supplies B+ to terminal 56 X2 of the ECM.



5. Ignition ON, test for 4.8-5.2 V between the 5 V reference circuit terminal 3 and ground



瀚慖f less than the specified range, test the 5 V reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,



replace the K20 ECM.



瀚慖f greater than the specified range, test the 5 V reference circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.



6. Ignition ON, verify that the scan tool IAT sensor parameter is colder than -39掳C (-38掳F).



瀚慖f warmer than the specified value, test the signal circuit terminal 2 for a short to ground. If the circuit/connections test normal, replace



the K20 ECM.



Note: If the fuse in the jumper wire opens, the signal circuit is shorted to a voltage and the sensor may be damaged.



7. Ignition ON, install a 3 A fused jumper wire between the signal circuit terminal 2 and ground. Verify the IAT sensor parameter is warmer



than 128掳C (263掳F).



瀚慖f colder than the specified value, test the signal circuit terminal 2 for an open or short to voltage. If the circuit/connections test normal,



replace the K20 ECM.



8. Ignition ON, install a 3 A fused jumper wire between the signal circuit terminal 2 and the 5 V reference circuit terminal 3.



Verify the IAT sensor parameter is colder than -39掳C (-38掳F).



瀚慖f warmer than the specified value, test the signal circuit for a short to ground. If the circuit/connections test normal, replace the K20



ECM.



9. If all circuits/connections test normal, test or replace the B65 Intake Manifold Pressure and Air Temperature sensor.

No comments:

Post a Comment