Skip to main content

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1400

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1400



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC P0506



- Idle Speed Low



DTC P0507



- Idle Speed High



DTC P050A



- Cold Start Idle Air Control System Performance



Circuit/System Description



The throttle actuator control (TAC) motor is a DC motor that is part of the throttle body assembly. The TAC motor drives the throttle valve. The



engine control module (ECM) controls the TAC motor based on throttle position sensor input. The idle speed is controlled by the ECM based on



various inputs. The ECM commands the TAC motor to open or close the throttle valve in order to maintain the desired idle speed. If the ECM



detects the actual idle speed is not within a predetermined range of the desired idle speed, this DTC sets.



Conditions for Running the DTC



* DTC P0111, P0112, P0113, P0116, P0117, P0118, P0119, P0121, P0122, P0123, P0221, P0222, P0223, P0335, P0336, P0338,



P2100-P2103 is not set.



* The engine load is less than 40 percent, for P0506.



* The engine coolant temperature (ECT) is warmer than 65掳C (149掳F), for P0506.



* The engine coolant temperature (ECT) is warmer than 69掳C (156掳F), for P0507.



* The intake air temperature (IAT) is warmer than -11掳C (+13掳F), for P0506.



* The engine speed is at idle.



* The engine is operating for greater than 100 s.



* The EVAP intrusive leak test is not enabled.



* The vehicle speed is 0 km/h (0 mph).



* The cold start idle speed control is not active.



* The evaporative emission (EVAP) canister purge valve command less than 40 percent.



* A vehicle speed was detected prior to the diagnostic running.



* DTC P0506 and P0507 run continuously once the above conditions are met for greater than 10 s.



Conditions for Setting the DTC



P0506



The actual engine speed is less than the desired idle speed by at least 100 RPM for greater than 1 s or for a cumulative time of 4 s.



P0507



* The actual engine speed is greater than the desired idle speed by at least 200 RPM for greater than 1 s or for a cumulative time of 4 s.



OR



* The ECM detects 3 fuel cut-offs due to an engine over speed condition while the vehicle speed is zero.



P050A



The actual engine speed is 100 RPM less or 200 RPM greater than the desired idle speed, for greater than 1 s or a cumulative of 4 s, during a cold



start.



Action Taken When the DTC Sets



DTCs P0506, P0507, and P050A are Type B DTCs.



Conditions for Clearing the DTC



DTCs P0506, P0507, and P050A are Type B DTCs.



Diagnostic Aids



Inspect for a condition in which the throttle valve may have been held open. For example, ice may have formed in the throttle bore.

Comments

Post a Comment

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...
Read more

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...
Post a Comment
Read more

D138， Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...
Post a Comment
Read more