Skip to main content

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Technical Service Bulletin # 05-03-10-020D Date: 120918

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Technical Service Bulletin # 05-03-10-020D Date: 120918



Wheels/Tires - Use Of Nitrogen Gas In Tires



INFORMATION



Bulletin No.: 05-03-10-020D



Date: September 18, 2012



Subject: Use of Nitrogen Gas in Tires



Models:



2013 and Prior GM Passenger Cars and Trucks



Supercede:



This bulletin is being revised to add the 2012 and 2013 model years. Please discard Corporate Bulletin Number 05-03-10-020C (Section 03 -



Suspension).



GM's Position on the Use of Nitrogen Gas in Tires



General Motors does not oppose the use of purified nitrogen as an inflation gas for tires. We expect the theoretical benefits to be reduced in



practical use due to the lack of an existing infrastructure to continuously facilitate inflating tires with nearly pure nitrogen. Even occasional inflation



with compressed atmospheric air will negate many of the theoretical benefits. Given those theoretical benefits, practical limitations, and the robust



design of GM original equipment TPC tires, the realized benefits to our customer of inflating their tires with purified nitrogen are expected to be



minimal.



2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 12



The Promise of Nitrogen: Under Controlled Conditions



Recently, nitrogen gas (for use in inflating tires) has become available to the general consumer through some retailers. The use of nitrogen gas to



inflate tires is a technology used in automobile racing. The following benefits under controlled conditions are attributed to nitrogen gas and its



unique properties:



- A reduction in the expected loss of Tire Pressure over time.



- A reduction in the variance of Tire Pressures with temperature changes due to reduction of water vapor concentration.



- A reduction of long term rubber degradation due to a decrease in oxygen concentrations.



Important



These are obtainable performance improvements when relatively pure nitrogen gas is used to inflate tires under controlled



conditions.



The Promise of Nitrogen: Real World Use



Nitrogen inflation can provide some benefit by reducing gas migration (pressure loss) at the molecular level through the tire structure. NHTSA



(National Highway Traffic Safety Administration) has stated that the inflation pressure loss of tires can be up to 5% a month. Nitrogen molecules



are larger than oxygen molecules and, therefore, are less prone to "seeping" through the tire casing. The actual obtainable benefits of nitrogen vary,



based on the physical construction and the materials used in the manufacturing of the tire being inflated.



Another potential benefit of nitrogen is the reduced oxidation of tire components. Research has demonstrated that oxygen consumed in the



oxidation process of the tire primarily comes from the inflation media. Therefore, it is reasonable to assume that oxidation of tire components can



be reduced if the tire is inflated with pure nitrogen. However, only very small amounts of oxygen are required to begin the normal oxidation



process. Even slight contamination of the tire inflation gas with compressed atmospheric air during normal inflation pressure maintenance, may



negate the benefits of using nitrogen.



GM Tire Quality, Technology and Focus of Importance



Since 1972, General Motors has designed tires under the TPC (Tire Performance Criteria) specification system, which includes specific



requirements that ensure robust tire performance under normal usage. General Motors works with tire suppliers to design and manufacture original



equipment tires for GM vehicles. The GM TPC addresses required performance with respect to both inflation pressure retention, and endurance



properties for original equipment tires. The inflation pressure retention requirements address availability of oxygen and oxidation concerns, while



endurance requirements ensure the mechanical structure of the tire has sufficient strength. This combination has provided our customers with tires



that maintain their structural integrity throughout their useful treadlife under normal operating conditions.



Regardless of the inflation media for tires (atmospheric air or nitrogen), inflation pressure maintenance of tires is critical for overall tire, and



ultimately, vehicle performance. Maintaining the correct inflation pressure allows the tire to perform as intended by the vehicle manufacturer in



many areas, including comfort, fuel economy, stopping distance, cornering, traction, treadwear, and noise. Since the load carrying capability of a



tire is related to inflation pressure, proper inflation pressure maintenance is necessary for the tire to support the load imposed by the vehicle without



excessive structural degradation.



Important



Regardless of the inflation media for tires (atmospheric air or nitrogen), inflation pressure maintenance of tires is critical for overall tire,



and ultimately, vehicle performance.

Comments

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138, Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...