Sunday, February 2, 2020

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1999

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1999



Reference Information



Schematic Reference



Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams/Electrical



Diagrams)



Connector End View Reference



Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit



Testing/Circuit Testing)



* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic



Procedures/Connector Repairs/Connector Repairs)



* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General



Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)



* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring



Repairs/Wiring Repairs)



Description and Operation



Transmission Component and System Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and



Operation/AF40-6 - Automatic Transmission/Transmission Component and System Description)



DTC Type Reference



Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code



(DTC) Type Definitions)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Circuit/System Verification



1. Ensure the transmission fluid temperature is between 50-80掳C (122-176掳F).



2. Operate the vehicle in 2nd gear long enough to ensure at least a 3掳C (5掳F) rise in transmission fluid temperature, then operate the vehicle in



Park for 5 s.



3. Observe the scan tool data TCC Pressure Control Solenoid Valve Current parameter. The reading should be between 0.1-1.1 A.



Circuit/System Testing



Command the TCC Solenoid Valve increase and decrease with a scan tool. The value should rise from 0.1-1.1 A and return to 0.1 A.



If the value does not change, turn ignition OFF, remove the K71 Transmission Control Module. Connect a test lamp between the low reference



circuit terminal 4 X2 at the K71 Transmission Control Module and the voltage supply component circuit terminal 9 X2 at the K71 Transmission



Control Module. Command the TCC Solenoid Valve increase and decrease with a scan tool. The test lamp has to illuminate brighter with increasing



current.



If the test lamp always illuminates or always does not illuminate, replace the K71 Transmission Control Module.



Component Testing



Static Test



1. Ignition OFF, remove the K71 Transmission Control Module.



2. Test for 5-5.6 ohm at 20掳C (68掳F) between the low reference circuit terminal 4 X2 and the voltage supply circuit terminal 9 X2.



瀚慖f less than the specified range, test the wiring harness for internal short. If the circuit test normal, replace the Q27D Pressure Control



Solenoid Valve 4.



3. Test for infinite resistance between each terminal and the low reference circuit terminal 4 X2 and also to the voltage supply circuit terminal 9



X2.



瀚慖f less than the specified range, replace the wiring harness.



4. If all circuit test normal, perform the control solenoid valve inspection. Refer to Control Solenoid Valve Inspection (M36 and MXE) (See:



Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/AF40-6 -



Automatic Transmission).



瀚慖f the inspection test normal, replace the control valve body.

No comments:

Post a Comment