2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2570
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
1. Ignition OFF, open the hood to disable the Auto-Stop function. Refer to Hybrid Modes of Operation Description ( See: Hybrid Drive
Systems/Description and Operation/Hybrid Modes of Operation).
2. Ignition ON, verify the scan tool hood position parameter displays Open.
瀚慖f the hood position does not display Open, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle) for DTC P254F.
3. Ignition ON, observe the scan tool 5-volt reference 1 and 2 circuit status parameters. The parameters should display OK.
4. Ignition ON, observe the DTC information with a scan tool. DTC P0641 and P0651 should not set on this ignition cycle.
5. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
Note: A short to voltage on the signal circuit of certain components may cause this DTC to set.
1. Ignition OFF, disconnect the harness connector of all appropriate sensors for the applicable DTC. Refer to Diagnostic Aids for the
appropriate sensors.
2. Ignition ON, measure for 4.8-5.2 V between one of the 5-volt reference circuits and ground.
瀚慖f less than the specified range, test for a short to ground on the 5-volt reference circuit for each affected component. If all circuits test
normal, replace the K20 ECM.
瀚慖f greater than the specified range, test for a short to voltage on the 5-volt reference circuit for each affected component. If all circuits test
normal, replace the K20 ECM.
3. Connect each component associated with the 5-volt reference circuit, one at a time, while monitoring the voltage. Verify the voltage remains
between 4.8-5.2 V.
瀚慖f not within the specified range when a component is connected, test the signal circuit for a short to voltage. If the circuit tests normal,
replace the component.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Accelerator Pedal Position Sensor Replacement (See: Powertrain Management/Computers and Control Systems/Accelerator Pedal Position
Sensor/Service and Repair)
* Air Conditioning (A/C) Refrigerant Pressure Sensor Replacement (Non-HP2) (See: Heating and Air Conditioning/Refrigerant Pressure
Sensor / Switch/Service and Repair/Air Conditioning (A/C) Refrigerant Pressure Sensor Replacement)Air Conditioning (A/C) Refrigerant
Pressure Sensor Replacement (HP2) (See: Heating and Air Conditioning/Refrigerant Pressure Sensor / Switch/Service and Repair/Air
Conditioning (A/C) Refrigerant Pressure Sensor Replacement)
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Sunday, February 23, 2020
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2570
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment