Skip to main content

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2516

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2516

Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle) for DTC P254F.

Circuit/System Testing

Note: An intermittent or momentary, less than 1 s, loss of system voltage during throttle tip-in may set DTC P060D.

1. Ignition ON, clear the DTC information with a scan tool. Observe the scan tool DTC information. Verify that DTCs P0602 or P2610 do not

fail this ignition cycle.

瀚慖f DTC P0602 failed this ignition, reprogram the ECM. Refer to Control Module References (See: Testing and Inspection/Programming

and Relearning). If DTC P0602 resets, replace the ECM.

瀚慖f DTC P2610 failed this ignition, test the ECM ignition, battery positive voltage, and ground circuits for an open/high resistance or a

short to ground. If the circuits test normal, replace the ECM.

2. Ignition ON, observe the DTC information with a scan tool. Verify DTCs P0601, P0603, P0604, P0606, P0607, P060D, P062F, or P16F3 do

not set this ignition cycle.

瀚慖f any of the DTCs set this ignition cycle, replace the ECM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, programming and setup

2ML70 - Automatic Transmission

DTC P0601-P0606, P060B, or P062F

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC P0601

- Transmission Control Module (TCM) Read Only Memory (ROM)

DTC P0602

- Transmission Control Module (TCM) Not Programmed

DTC P0603

- Transmission Control Module (TCM) Long Term Memory Reset

DTC P0604

- Transmission Control Module (TCM) Random Access Memory (RAM)

DTC P0606

- Transmission Control Module (TCM) Internal Performance

DTC P060B

- Control Module Analog to Digital Performance

DTC P062F

- Transmission Control Module (TCM) Long Term Memory Performance

Circuit/System Description

This is an internal fault detection of the transmission control module. This fault is handled inside the transmission control module and no external

circuits are involved. The transmission control module is part of the control solenoid valve assembly, and is not serviced separately.

Conditions for Running the DTC

* The control solenoid valve assembly runs the program to detect an internal fault when the key is ON or the engine is running.

Comments

Post a Comment

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...
Read more

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...
Post a Comment
Read more

D138， Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...
Post a Comment
Read more