2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1597
The shift control solenoid assembly (SLC1, SLC2, SLC3, SLB1) and the line pressure control solenoid (SLT) are installed on the front valve body.
The solenoids linearly control hydraulic pressure in response to signals output from the transmission control module (TCM). SLC1, SLC2, SLC3,
SLB1 controls hydraulic pressure to the clutches (C1, C2, C3) and brake (B1) for smooth shifting. According to each shift control solenoid
assembly, the transmission shifts from 1st gear to 6th gear and vice versa. As a fail-safe function, if any shift control solenoid assembly abnormality
occurs, the TCM will disable the current to the solenoids.
Conditions for Running the DTC
* The ignition voltage is 10.2-15.5 V.
* The engine speed is greater than 400 RPM for 2 s.
* The transmission is not in emergency mode.
* TCM communication is normal.
* Transmission fluid temperature is higher than 20掳C (68掳F).
* DTCs P0716, P0717, P0721 and P0722 are not set.
Conditions for Setting the DTC
* Driving in D range, 2nd gear.
* Output speed more than 500 RPM.
* Throttle position more than 10%.
* Measured gear ratio deviates more than 20% from expected ratio.
* Measured gear ratio deviates within 4% from 1st, 3rd, 4th or 6th gear ratio.
* Determined after 12 times lasting 1 s or more.
Action Taken When the DTC Sets
* DTC P0732 is a Type C DTC.
* Torque limitation in "D" range 150 Nm (110 lb ft), in "R" range 170 Nm (125 lb ft).
* The TCM freezes transmission adaptive functions.
* The TCM turns OFF all solenoids.
* The TCM allows the vehicle after a stop to operate only in the second gear and "R" range.
Conditions for Clearing the DTC
* DTC P0732 is a Type C DTC.
* Measured gear ratio deviates less than 4% from expected ratio.
Diagnostic Aids
When attempting to set transmission performance DTCs, observe the Freeze Frame/Failure Records to assist in duplicating the inoperative or
affected conditions. Ensure the transmission fluid level, color and odor is correct and there are no leaks. If there are any other transmission DTCs
set, diagnose those first.
Reference Information
Schematic Reference
Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams/Electrical
Diagrams)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Description and Operation
Transmission Component and System Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and
Operation/AF40-6 - Automatic Transmission/Transmission Component and System Description)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
No comments:
Post a Comment