2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1333

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1333

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance or for a short to voltage. If the

circuit/connections test normal, replace the ECM.

4. Install the fuse that supplies B+ to terminal 56-X2 of the ECM.

5. Ignition ON, test for greater than 4.8 V between the 5-volt reference circuit terminal 3 and ground.

瀚慖f less than the specified value, test the 5-volt reference circuit for an open/high resistance. If the circuits/connections test normal, replace

the ECM.

6. Test for 4.8-5.2 V between the signal circuit terminal 2 and ground.

瀚慖f the voltage is greater than specified range, test for a short to voltage in the signal circuit. If circuit/connections test normal, replace the

ECM.

瀚慖f the voltage is less than the specified range, test for a short to ground or an open/high resistance in the signal circuit. If

circuit/connections test normal, replace the ECM.

7. If all circuits/connections test normal, replace the camshaft position sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust (See: Powertrain Management/Computers and Control

Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust)

* Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake (See: Powertrain Management/Computers and Control

Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake)

* Camshaft Position Sensor Replacement - Bank 1 (Right Side) Exhaust (See: Powertrain Management/Computers and Control

Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 1 (Right Side) Exhaust)

* Camshaft Position Sensor Replacement - Bank 1 (Right Side) Intake (See: Powertrain Management/Computers and Control

Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 1 (Right Side) Intake)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for engine control module replacement, setup, and

programming

P0392

DTC P0341, P0342, P0343, P0346, P0347, P0348, P0366, P0367, P0368, P0391, P0392, or P0393 (LAU)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0341

- Intake Camshaft Position Sensor Performance Bank 1

DTC P0342

- Intake Camshaft Position Sensor Circuit Low Voltage Bank 1

DTC P0343

- Intake Camshaft Position Sensor Circuit High Voltage Bank 1

DTC P0346

- Intake Camshaft Position Sensor Performance Bank 2

DTC P0347

- Intake Camshaft Position Sensor Circuit Low Voltage Bank 2

DTC P0348

- Intake Camshaft Position Sensor Circuit High Voltage Bank 2

DTC P0366

- Exhaust Camshaft Position Sensor Performance Bank 1