Skip to main content

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 705

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 705

1. Ignition OFF, disconnect the harness connector at the adjustable pedal switch.

2. Test for infinite resistance between the 12-volt reference terminal 11 and the signal terminals listed below:

* Terminal 10

* Terminal 12

瀚慖f not the specified value, replace the adjustable pedal switch.

3. Adjustable pedal switch in the FWD position, test for less than 2 ohms between the 12-volt reference terminal 11 and the signal terminal 12.

瀚慖f greater than the specified range, replace the adjustable pedal switch.

4. Adjustable pedal switch in the RWD position, test for less than 2 ohms between the 12-volt reference terminal 11 and the signal terminal 10.

瀚慖f greater than the specified range, replace the adjustable pedal switch.

Z75

1. Ignition OFF, disconnect the harness connector at the adjustable pedal switch.

2. Test for infinite resistance between the 12-volt reference terminal 5 and the signal terminals listed below:

* Terminal 4

* Terminal 6

瀚慖f not the specified value, replace the adjustable pedal switch.

3. Adjustable pedal switch in the FWD position, test for less than 2 ohms between the 12-volt reference terminal 5 and the signal terminal 6.

瀚慖f greater than the specified range, replace the adjustable pedal switch.

4. Adjustable pedal switch in the RWD position, test for less than 2 ohms between the 12-volt reference terminal 5 and the signal terminal 4.

瀚慖f greater than the specified range, replace the adjustable pedal switch.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Accessory Switch Replacement (Except Cadillac) (See: Instrument Panel, Gauges and Warning Indicators/Service and Repair/Accessory

Switch Replacement (Except Cadillac))Accessory Switch Replacement (Cadillac) (See: Instrument Panel, Gauges and Warning

Indicators/Service and Repair/Accessory Switch Replacement (Cadillac))

* Control Module References (See: Testing and Inspection/Programming and Relearning) for the MSM replacement, setup, and programming

B3605

DTC B3604 or B3605

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC B3604 01

- Adjustable Foot Pedal Forward Switch Circuit Short to Battery

DTC B3605 01

- Adjustable Foot Pedal Rearward Switch Circuit Short to Battery

Diagnostic Fault Information

Comments

Post a Comment

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...
Read more

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...
Post a Comment
Read more

D138， Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...
Post a Comment
Read more