2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 683
* When the fault is no longer present, the DTC will be a history DTC.
* A history DTC will clear after 50 ignition cycles.
Diagnostic Aids
B3205 0B can be set due to excessive physical resistance in the window regulator assembly. Ensure proper mechanical operation of the regulator
assembly prior to replacing electrical components.
Reference Information
Schematic Reference
Moveable Window Schematics (See: Windows and Glass/Windows/Diagrams/Electrical Diagrams)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Power Windows Description and Operation (See: Windows and Glass/Windows/Description and Operation/Power Windows Description and
Operation)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
Observe the operation of the power windows while commanding each window UP and DOWN by using their respective window switches, each
window should perform the UP and DOWN function.
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the appropriate window motor.
2. Connect a test lamp between control circuit terminal A and control circuit terminal B.
3. Ignition ON, command the window UP and DOWN by using the door switch. The test lamp should turn ON when commanding the UP and
DOWN states.
瀚慖f the test lamp is always OFF during either of the commands, test either control circuit for a short to ground or open/high resistance. If
the circuits test normal, replace the door switch.
瀚慖f the test lamp is always ON, test either control circuit for a short to voltage. If the circuits test normal, replace the door switch
4. If all circuits test normal, test or replace the window motor.
Component Testing
Important: When performing the following tests, make sure that the window motor is not all ready in the position the test is attempting to
produce.
1. Ignition OFF, disconnect the harness connector at the appropriate window motor.
2. Install a 25A fused jumper wire between the control terminal A and 12 volts. Momentarily install a jumper wire between the control terminal
B and ground. The window motor should perform the UP or DOWN function.
瀚慖f the function does not perform as specified, replace the window motor.
3. Reverse the jumper wires; the window motor should perform the DOWN or UP function.
瀚慖f the function does not perform as specified, replace the window motor
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Thursday, December 5, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 683
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment