2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 918
Primary Piston Position Sensor A parameter is greater than 4.5 V.
瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the EBCM.
6. Verify the scan tool BMC Primary Piston Position Sensor B parameter is less than 1 V.
瀚慖f greater than the specified range, test the signal circuit terminal 1 for a short to voltage. If the circuit tests normal, replace the EBCM.
7. Install a 3A fused jumper wire between the signal circuit terminal 1 and the 5 V reference circuit terminal 2. Verify the scan tool BMC
Primary Piston Position Sensor B parameter is greater than 4.5 V.
瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the EBCM.
8. If all circuits test normal, replace the brake master cylinder piston position sensor. If DTC resets, replace the EBCM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Brake Master Cylinder Primary Piston Position Sensor Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction Control
Systems/Braking Sensor/Switch/Service and Repair)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for EBCM replacement, setup, and programming
Brake Pedal Position Sensor 3 Not Plausible
DTC C0277, C120C, C129A, C129B, C129D, C129E, C12B1, or C12F8
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC C0277 03
- BMC Primary Piston Position Sensor A and B Circuit Performance Voltage Below Threshold
DTC C129A
- Brake Pedal Position Sensor 3 Circuit Low
DTC C129D
- Brake Pedal Position Sensor 4 Circuit Low
DTC C0277 07
- BMC Primary Piston Position Sensor A and B Circuit Voltage Above Threshold
DTC C129B
- Brake Pedal Position Sensor 3 Circuit High
DTC C129E
- Brake Pedal Position Sensor 4 Circuit High
DTC C0277 5A
- BMC Primary Piston Position Sensor A and B Circuit Plausibility Failure
DTC C12B1
- ABS Master Cylinder Pressure Sensor and Brake Pedal Position Sensor Not Plausible
DTC C12F8
- Brake Pedal Position Sensor 3 Not Plausible
DTC C120C
- Brake Pedal Position Sensor 4 Not Plausible
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Monday, December 16, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 918
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment