2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 707
2. Ignition ON, test for 11.8-12.2 volts between the appropriate 12-volt reference circuit listed below and ground:
* X88/Z88 - terminal 11
* Z75 - terminal 5
瀚慖f greater than the specified range, test the 12-volt reference circuit for a short to voltage. If the circuit tests normal, replace the MSM.
瀚慖f less than the specified range, test the 12-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests
normal, replace the MSM.
3. Verify the scan tool Pedal Forward Switch parameter is Inactive.
瀚慖f not the specified value, test the appropriate signal circuit terminal listed below for a short to voltage. If the circuit tests normal, replace
the MSM.
* X88/Z88 - terminal 12
* Z75 - terminal 6
4. Verify the scan tool Pedal Aft Switch parameter is Inactive.
瀚慖f not the specified value, test the appropriate signal circuit terminal listed below for a short to voltage. If the circuit tests normal, replace
the MSM.
* X88/Z88 - terminal 10
* Z75 - terminal 4
5. Install a 3A fused jumper wire between the appropriate signal circuit terminal listed below and B+. The scan tool Pedal Forward Switch
parameter should be Active.
* X88/Z88 - terminal 12
* Z75 - terminal 6
瀚慖f not the specified value, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the
MSM.
6. Install a 3A fused jumper wire between the appropriate signal circuit terminal listed below and B+. The scan tool Pedal Aft Switch parameter
should be Active.
* X88/Z88 - terminal 10
* Z75 - terminal 4
瀚慖f not the specified value, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the
MSM.
7. If all circuits test normal, test or replace the adjustable pedal switch.
Component Testing
X88/Z88
1. Ignition OFF, disconnect the harness connector at the adjustable pedal switch.
2. Test for infinite resistance between the 12-volt reference terminal 11 and the signal terminals listed below:
* Terminal 10
* Terminal 12
瀚慖f not the specified value, replace the adjustable pedal switch.
3. Adjustable pedal switch in the FWD position, test for less than 2 ohms between the 12-volt reference terminal 11 and the signal terminal 12.
瀚慖f greater than the specified range, replace the adjustable pedal switch.
4. Adjustable pedal switch in the RWD position, test for less than 2 ohms between the 12-volt reference terminal 11 and the signal terminal 10.
瀚慖f greater than the specified range, replace the adjustable pedal switch.
Z75
1. Ignition OFF, disconnect the harness connector at the adjustable pedal switch.
2. Test for infinite resistance between the 12-volt reference terminal 5 and the signal terminals listed below:
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Friday, December 6, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 707
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment