Skip to main content

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 810

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 810

- EBCM Unimplemented Interrupt

DTC C121F

- EBCM Unexpected Exception

DTC C123A

- EBCM High End Timer Watchdog

DTC C123B

- EBCM High End Timer Program Overflow

DTC C123C

- EBCM High End Timer RAM Fault

DTC C123D

- EBCM Solenoid Timeout

DTC C123E

- EBCM High End Timer Periodic Interrupt

DTC C123F

- EBCM Serial Peripheral Interface Inoperative

DTC C1255

- Electronic Control Unit Performance

DTC C1256

- Program ROM Checksum Error

DTC C126E

- EBCM Stack Overrun

DTC C126F

- EBCM Serial Peripheral Interface Performance

DTC C127C

- EBCM Self Test Failed

DTC C127E

- EBCM Module High Temperature

DTC C12A7

- ABS Boost Valve Solenoid Circuit Performance

DTC C12C2

- ABS Left Front Isolation Solenoid Valve Driver Shorted

DTC C12C5

- ABS Right Front Isolation Solenoid Valve Diver Shorted

DTC C12C6

- ABS Left Rear Isolation Solenoid Valve Circuit Failure

DTC C12C8

- ABS Right Rear Isolation Solenoid Valve Circuit Failure

DTC C12CC

- ABS Left Front Dump Solenoid Valve Driver Shorted

DTC C12CF

- ABS Right Front Dump Solenoid Valve Driver Shorted

DTC C12D0

- ABS Left Rear Dump Solenoid valve Circuit Open

DTC C12D1

- ABS Left Rear Dump Solenoid Valve Circuit Shorted

DTC C12D2

- ABS Left Rear Dump Solenoid Valve Driver Shorted

Comments

Post a Comment

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...
Read more

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...
Post a Comment
Read more

D138， Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...
Post a Comment
Read more