2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 681
Reference Information
Schematic Reference
Door Lock/Indicator Schematics (See: Body and Frame/Locks/Diagrams/Electrical Diagrams/Door Lock/Indicator Schematics)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Power Door Locks Description and Operation (See: Body and Frame/Locks/Power Locks/Description and Operation)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
Command the Lock Rear Doors and Unlock Rear Doors with a scan tool, the rear doors should perform the LOCK and UNLOCK function.
Circuit/System Testing
1. Ignition OFF, disconnect the X3 harness connector at the I/P fuse block.
2. Connect a test lamp between the control circuit terminal A2 and ground.
3. Ignition ON, command the Lock Rear Doors with a scan tool. The test lamp should briefly illuminate during the LOCK command.
瀚慖f the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the BCM.
瀚慖f the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the BCM.
4. Connect a test lamp between the control circuit terminal A3 and B+.
5. Command the Unlock Rear Doors with a scan tool. The test lamp should briefly illuminate during the UNLOCK command.
瀚慖f the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace
the BCM.
瀚慖f the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the BCM.
6. If all circuits test normal, replace the I/P fuse block.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Instrument Panel Electrical Center or Junction Block Replacement - Left Side (See: Maintenance/Fuses and Circuit Breakers/Fuse
Block/Service and Repair/Removal and Replacement/Instrument Panel Electrical Center or Junction Block Replacement - Left Side)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, setup and programming
B3205
DTC B3205
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
Reference Information
Schematic Reference
Door Lock/Indicator Schematics (See: Body and Frame/Locks/Diagrams/Electrical Diagrams/Door Lock/Indicator Schematics)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Power Door Locks Description and Operation (See: Body and Frame/Locks/Power Locks/Description and Operation)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
Command the Lock Rear Doors and Unlock Rear Doors with a scan tool, the rear doors should perform the LOCK and UNLOCK function.
Circuit/System Testing
1. Ignition OFF, disconnect the X3 harness connector at the I/P fuse block.
2. Connect a test lamp between the control circuit terminal A2 and ground.
3. Ignition ON, command the Lock Rear Doors with a scan tool. The test lamp should briefly illuminate during the LOCK command.
瀚慖f the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the BCM.
瀚慖f the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the BCM.
4. Connect a test lamp between the control circuit terminal A3 and B+.
5. Command the Unlock Rear Doors with a scan tool. The test lamp should briefly illuminate during the UNLOCK command.
瀚慖f the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace
the BCM.
瀚慖f the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the BCM.
6. If all circuits test normal, replace the I/P fuse block.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Instrument Panel Electrical Center or Junction Block Replacement - Left Side (See: Maintenance/Fuses and Circuit Breakers/Fuse
Block/Service and Repair/Removal and Replacement/Instrument Panel Electrical Center or Junction Block Replacement - Left Side)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, setup and programming
B3205
DTC B3205
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
Comments
Post a Comment