2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 666
Ignition ON, observe the scan tool BCM Hood Open Switch and Hood Closed Switch parameters. With the hood open, the Hood Open Switch
parameter should read Active and the Hood Closed Switch parameter should read Inactive. With the hood closed, the Hood Open Switch parameter
should read Inactive and the Hood Closed Switch parameter should read Active.
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the hood ajar switch.
2. Ignition OFF, test for less than 5 ohms between the ground circuit terminal C and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
3. Ignition ON, test for 11.5-12.0 volts between the signal circuit terminal A and ground.
瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the BCM.
瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the BCM.
4. Ignition ON, test for 11.5-12.0 volts between the signal circuit terminal B and ground.
瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the BCM.
瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the BCM.
5. If all circuits test normal, test or replace the hood ajar switch.
Component Testing
Hood Ajar Switch
1. Ignition OFF, disconnect the harness connector at the hood ajar switch.
2. With the switch in the hood closed position, test for infinite resistance between the ground terminal C and the signal terminal A.
瀚慖f not infinite, replace the hood ajar switch.
3. Test for less than 2.0 ohms between the ground terminal C and the signal terminal B.
瀚慖f greater than the specified range, replace the hood ajar switch.
4. With the switch in the hood open position, test for infinite resistance between the ground terminal C and the signal terminal B.
瀚慖f not infinite, replace the hood ajar switch.
5. Test for less than 2.0 ohms between the ground terminal C and the signal terminal A.
瀚慖f greater than the specified range, replace the hood ajar switch.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Hood Primary and Secondary Latch Replacement (See: Body and Frame/Doors, Hood and Trunk/Hood/Hood Latch/Service and Repair)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, programming and setup
B3031
DTC B3031
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Wednesday, December 4, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 666
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment