2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 630
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Testing
1. Ignition OFF, disconnect the X4 harness connector at the underhood fuse block.
2. Connect a test lamp between the control circuit terminal C3 and B+.
3. Command the High Beams ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded
states.
瀚慖f the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the BCM.
瀚慖f the test lamp is always OFF, test the control circuit for a short to voltage or open/high resistance. If the circuit tests normal, replace the
BCM.
4. If all circuits test normal, test or replace the underhood fuse block.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Underhood Electrical Center or Junction Block Replacement (See: Maintenance/Fuses and Circuit Breakers/Fuse Block/Service and
Repair/Removal and Replacement/Underhood Electrical Center or Junction Block Replacement)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, setup, and programming
B2585
DTC B2585
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC B2585 00
- Park Lamp Control Circuit
Diagnostic Fault Information
Circuit/System Description
Voltage is applied at all times to the park lamp relay from battery voltage. When the headlamp switch is placed in the PARK position and the body
control module (BCM) commands the park lamps ON, the BCM then applies a ground to the park lamp relay control circuit. This engages the relay
and applies voltage through the park lamp fuses and to all the park, license, and tail lamps.
Conditions for Running the DTC
* The Ignition is ON.
* The park lamps must be commanded ON by the BCM.
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Testing
1. Ignition OFF, disconnect the X4 harness connector at the underhood fuse block.
2. Connect a test lamp between the control circuit terminal C3 and B+.
3. Command the High Beams ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded
states.
瀚慖f the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the BCM.
瀚慖f the test lamp is always OFF, test the control circuit for a short to voltage or open/high resistance. If the circuit tests normal, replace the
BCM.
4. If all circuits test normal, test or replace the underhood fuse block.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Underhood Electrical Center or Junction Block Replacement (See: Maintenance/Fuses and Circuit Breakers/Fuse Block/Service and
Repair/Removal and Replacement/Underhood Electrical Center or Junction Block Replacement)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, setup, and programming
B2585
DTC B2585
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC B2585 00
- Park Lamp Control Circuit
Diagnostic Fault Information
Circuit/System Description
Voltage is applied at all times to the park lamp relay from battery voltage. When the headlamp switch is placed in the PARK position and the body
control module (BCM) commands the park lamps ON, the BCM then applies a ground to the park lamp relay control circuit. This engages the relay
and applies voltage through the park lamp fuses and to all the park, license, and tail lamps.
Conditions for Running the DTC
* The Ignition is ON.
* The park lamps must be commanded ON by the BCM.
Comments
Post a Comment