Wednesday, November 6, 2019

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 2002

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 2002



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Special Tools



DT-47825-20 Adapter Harness



Circuit/System Verification



1. Operate the vehicle in second gear long enough to ensure at least a 3掳C (5掳F) rise in TCM temperature.



2. Operate the vehicle in drive range and ensure TCC is commanded ON for 1 minute. Verify with a scan tool the following test status



parameters display OK:



* TCC PC Sol. Perf. Test Status



* TCC PC Sol. Ctrl. Ckt. High Voltage Test Status



* TCC PC Sol. Ctrl. Ckt. Low Voltage Test Status



3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the



conditions that you observed from the Freeze Frame/Failure Records data.



Circuit/System Testing



Note: You must perform the Circuit/System Verification first.



1. Ignition OFF, remove the control solenoid valve assembly. Refer to Control Solenoid Valve and Transmission Control Module Assembly



Replacement (See: Powertrain Management/Transmission Control Systems/Actuators and Solenoids - Transmission and



Drivetrain/Actuators and Solenoids - A/T/Shift Solenoid/Service and Repair).



2. Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and Drivetrain/Automatic



Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/6T70/6T75 - Automatic Transmission/Control



Solenoid Valve and Transmission Control Module Assembly Inspection).



3. Place the control solenoid valve assembly on a clean work surface near the transmission assembly.



4. Connect the DT-47825-20 adapter harness between the vehicle wire harness electrical connector, and the control solenoid valve assembly



electrical connector.



5. Ignition ON, verify with a scan tool the following test status parameters display OK:



* TCC PC Sol. Perf. Test Status



* TCC PC Sol. Ctrl. Ckt. High Voltage Test Status



* TCC PC Sol. Ctrl. Ckt. Low Voltage Test Status



瀚慖f any test status parameter displays Fault or Malfunction, replace the control solenoid valve assembly.



Repair Instructions



Note:



* Perform the Service Fast Learn Adapts (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and



Inspection/Programming and Relearning) following all transmission related repairs.



* Before replacing the TCM, perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission



and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/6T70/6T75 - Automatic



Transmission/Control Solenoid Valve and Transmission Control Module Assembly Inspection).



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



Control Module References (See: Testing and Inspection/Programming and Relearning) for control solenoid valve assembly replacement, setup,



and programming



AF40-6 - Automatic Transmission



DTC P2759 or P2762-P2764



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.

No comments:

Post a Comment