2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1188

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1188

DTCs P0244, P0245, P0246 are Type B DTCs.

Conditions for Clearing the MIL/DTCs

DTCs P0244, P0245, P0246 are Type B DTCs.

Reference Information

Schematic Reference

Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Turbocharger System Description (See: Powertrain Management/Fuel Delivery and Air Induction/Turbocharger/Description and Operation)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Engine running, command the Turbocharger Wastegate Solenoid Valve to 20% with a scan tool while observing the following control circuit

status parameters:

* Turbocharger Wastegate Solenoid Valve Control Circuit High Voltage Test Status

* Turbocharger Wastegate Solenoid Valve Control Circuit Open Test Status

* Turbocharger Wastegate Solenoid Valve Control Circuit Low Voltage Test Status

Each parameter should display OK.

2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Inspect the turbocharger and the wastegate solenoid valve for damage. Refer to Turbocharger Cleaning and Inspection (See: Engine,

Cooling and Exhaust/Engine/Service and Repair/Overhaul/102. Turbocharger Cleaning and Inspection)

2. Ignition OFF, disconnect the harness connector at the Q42 turbocharger wastegate solenoid valve.

3. Ignition ON, verify that a test lamp illuminates between the ignition circuit terminal 1 and ground.

瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit tests normal and

the ignition circuit fuse is open, test all components connected to the ignition circuit and replace as necessary.

4. Connect a test lamp between the control circuit terminal 2 and the ignition circuit terminal 1.

5. Command the Turbocharger Wastegate Solenoid Valve to 50% with a scan tool. The test lamp should illuminate when commanded to 50%

and turn OFF when commanded to 0%.

瀚慖f the test lamp is always ON, test the control circuit terminal 2 for a short to ground. If the circuit tests normal, replace the K20 ECM.

瀚慖f the test lamp is always OFF, test the control circuit terminal 2 for a short to voltage or an open/high resistance. If the circuit tests

normal, replace the K20 ECM.

6. Test for 2.6-4.6 V between the control circuit terminal 2 and ground.