Skip to main content

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1627

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1627



* The transmission fluid temperature is 0掳C (32掳F) or greater.



* No DTCs P0101, P0102, P0103, P0106, P0107, P0108, P0171, P0172, P0174, P0175, P0201, P0202, P0203, P0204, P0205, P0206, P0207,



P0208, P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308, P0401, P042E, P0716, P0717, P0722, P0723, or P182E.



P0752



* The ignition voltage is greater than 8.6 volts.



* The engine speed is 400 RPM or greater for 5.0 seconds.



* The high side driver is enabled.



* The throttle position signal is valid.



* The output shaft speed is greater than 0 RPM, or the throttle position is greater than 0.4 percent.



* The transmission fluid temperature is 0掳C (32掳F) or greater.



Conditions for Setting the DTC



P0751



Commanded gear equals first lock, the gear ratio is 1.34-1.48, and gear box slip is greater than 200 RPM for 0.3 second, 8 times.



P0752



The transmission has achieved 1st Locked, 1st Free-Wheel, or 2nd, the 456/R1 pressure switch is pressurized, and gear box slip is greater than 200



RPM for 2 seconds, 5 times.



Action Taken When the DTC Sets



P0751



* DTC P0751 is a Type B DTC.



* The TCM inhibits first range.



P0752



* DTC P0752 is a Type A DTC.



* The TCM freezes transmission adaptive functions.



* The TCM commands maximum line pressure.



* The TCM inhibits Tap Up/Down function.



* The TCM inhibits manual shifting of forward gears.



* The TCM limits the transmission to reverse, first, and third range operation.



Conditions for Clearing the DTC



P0751



DTC P0751 is a Type B DTC.



P0752



DTC P0752 is a Type A DTC.



Diagnostic Aids



Before performing a road test, configure and setup the scan tool for snapshot mode. This allows you to display, monitor, and verify multiple



transmission data parameters at one time, after the road test.



Reference Information



Schematic Reference



Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams)



Connector End View Reference



* Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)



* Inline Harness Connector End Views (See: Diagrams/Connector Views/Multiple Junction Connector/Connector End Views By Number)



Description and Operation



Transmission General Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and Operation/6T70/6T75 -



Automatic Transmission/Transmission General Description)



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit



Testing/Circuit Testing)



* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Comments

Post a Comment

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...
Read more

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...
Post a Comment
Read more

D138， Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...
Post a Comment
Read more