2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 697
Circuit/System Verification
Ignition ON,observe the scan tool Tilt Up Switch parameter and Tilt Down Switch parameter while cycling the switch between states.The reading
should be Inactive and change to Active when pushing the appropriate switch.
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the tilt switch.
2. Ignition ON, verify a test lamp illuminates between the B+ circuit terminal B and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.
3. Verify the scan tool tilt switch parameter is Inactive.
瀚慖f not the specified value, test the control circuit listed below for a short to voltage. If the circuit tests normal, replace the MSM.
* Tilt Up Switch terminal C
* Tilt Down Switch terminal A
4. Install a 3A fused jumper wire between the control circuits listed below and the B+ circuit terminal. Verify the scan tool tilt switch parameter
is Active.
* Tilt Up Switch terminal C
* Tilt Down Switch terminal A
瀚慖f not the specified value, test the appropriate control circuit for a short to ground or an open/high resistance. If the circuit tests normal,
replace the MSM.
5. If all circuit test normal, test or replace the tilt switch.
Component Testing
Tilt Switch
1. Ignition OFF, disconnect the harness connector at the tilt switch.
2. Test for infinite resistance between the control terminals A and C with the switch in the neutral position.
瀚慖f less than the specified range, replace the tilt switch.
3. Test for less than 1 ohm between the control terminals listed below and the B+ terminal B with the switch in each appropriate position.
* Tilt Up Switch terminal C
* Tilt Down Switch terminal A
瀚慖f greater than the specified value, replace the tilt switch.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Steering Column Tilt Wheel Switch Replacement (See: Sensors and Switches/Sensors and Switches - Steering and Suspension/Sensors and
Switches - Steering/Tilt Wheel Switch/Service and Repair)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for MSM replacement, setup, and programming
B2860
DTC B2860 or B2880
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
Circuit/System Verification
Ignition ON,observe the scan tool Tilt Up Switch parameter and Tilt Down Switch parameter while cycling the switch between states.The reading
should be Inactive and change to Active when pushing the appropriate switch.
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the tilt switch.
2. Ignition ON, verify a test lamp illuminates between the B+ circuit terminal B and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.
3. Verify the scan tool tilt switch parameter is Inactive.
瀚慖f not the specified value, test the control circuit listed below for a short to voltage. If the circuit tests normal, replace the MSM.
* Tilt Up Switch terminal C
* Tilt Down Switch terminal A
4. Install a 3A fused jumper wire between the control circuits listed below and the B+ circuit terminal. Verify the scan tool tilt switch parameter
is Active.
* Tilt Up Switch terminal C
* Tilt Down Switch terminal A
瀚慖f not the specified value, test the appropriate control circuit for a short to ground or an open/high resistance. If the circuit tests normal,
replace the MSM.
5. If all circuit test normal, test or replace the tilt switch.
Component Testing
Tilt Switch
1. Ignition OFF, disconnect the harness connector at the tilt switch.
2. Test for infinite resistance between the control terminals A and C with the switch in the neutral position.
瀚慖f less than the specified range, replace the tilt switch.
3. Test for less than 1 ohm between the control terminals listed below and the B+ terminal B with the switch in each appropriate position.
* Tilt Up Switch terminal C
* Tilt Down Switch terminal A
瀚慖f greater than the specified value, replace the tilt switch.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Steering Column Tilt Wheel Switch Replacement (See: Sensors and Switches/Sensors and Switches - Steering and Suspension/Sensors and
Switches - Steering/Tilt Wheel Switch/Service and Repair)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for MSM replacement, setup, and programming
B2860
DTC B2860 or B2880
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
Comments
Post a Comment