Skip to main content

Nissan Altima CVT Class Action Lawsuit May Be Settled



A Nissan Altima CVT class action lawsuit may soon be settled for former and current owners and lessees of about 1.4 million cars.



The proposed Altima continuously variable transmission (CVT) class action lawsuit settlement includes five separate actions:




According to the lawsuits, the 2013-2016 Altima CVTs hesitate, shudder, shake and make noise before they finally fail. The slow response times of the Altima transmissions allegedly make the cars dangerous to drive on highways, especially when the cars stall.



Some Altima customers claim they spent thousands of dollars to repair or replace the transmissions, and customers claim replacement CVTs are just as defective as the originals.



The lawsuit also references technical service bulletins Nissan sent to dealerships because Altima customers were complaining about the transmissions.



In the proposed settlement, Nissan has agreed to extend the transmission assembly warranty by 24 months or 24,000 miles, whichever occurs first. However, the CVT warranty extension will still be subject to the original new vehicle limited warranty.



This means an Altima owner could still be denied coverage if Nissan decides the CVT problems are caused by "damage resulting from alteration, tampering, improper repair, misuse, environmental conditions, and lack of or improper maintenance."



The automaker will also reimburse customers for replacements or repairs to the transmission assemblies or transmission control units, but only for qualifying repairs. To receive reimbursements, customers must have paid for repairs or replacements for work performed after the powertrain warranties expired.



If the replacement or repair was performed by a Nissan dealer, the full amount paid will be reimbursed, but if the work was performed by a non-Nissan repair facility, Nissan will reimburse up to $5,000 for that repair or replacement.



Another condition for reimbursement is the replacement or repairs must have occurred on or before the vehicle was in service for 84 months or driven for 84,000 miles, whichever occurs first.



As for a former 2013-2016 Altima owner, they may be eligible for a $1,000 voucher toward the purchase or lease of a new Infiniti or Nissan vehicle as long as specific conditions are met.



The former owner must have had two or more replacements or repairs to the transmission assembly or the control unit and supported by all necessary documentation. In addition, the voucher expires nine months from the effective date of the settlement.



A former owner will not qualify for the voucher if the repairs consisted of prior software updates and/or reprogramming.



According to court documents, Nissan has agreed to pay $5.9 million to the lawyers representing Altima owners.



Although Nissan agreed to settle the CVT class action lawsuit, a federal judge must still look things over and give final approval.



The Nissan Altima CVT class action lawsuit was filed in the U.S. District Court for the Middle District of Tennessee.



The plaintiffs are represented by Barnow and Associates, Blood Hurst & O’Reardon, Glancy, Prongay & Murray, and Sanford Heisler Sharp.



SOURCE: CarComplaints.comNissan Altima CVT Class Action Lawsuit May Be Settled



CARCOMPLAINTS.COM RSS FEED (https://www.carcomplaints.com/news/feed.xml)
© 2019 Autobeef LLC. RSS Terms of Use: https://www.carcomplaints.com/rss.shtml
Mon Jul 8 10:37:14 2019 | 38.121.82.246 | Mozilla/5.0 (Macintosh; U; PPC Mac OS X 10_5_2; en-gb) AppleWebKit/526+ (KHTML, like Gecko) Version/3.1 iPhone | GET | ZCXVCBASDF

Comments

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138, Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...