Tuesday, June 4, 2019

Mercedes-Benz A220 2020 Technical Service Bulletin # LI82-61_P-0559542 Date: 130424


Navigation - Becker(R)MAP PILOT 'No Navigation Module Connected



Becker MAP PILOT: Message "No navigation module connected" appears in the display



Topic number L182.61-P-055954



Version 2



Design group 82.61 Auto pilot system (APS), Audio 30 APS



Date 04-24-2013



Validity Model 117, 166, 172, 176, 204, 207, 212, 218, 242, 246



with Becker MAP PILOT (code 509) or preinstallation for



Becker MAP PILOT (code 508)



Reason for change



Complaint:



The Audio/COMAND display (A40/8) of the Becker MAP Pilot continuously or intermittently shows the message "No navigation module



Mercedes-Benz A220 2020 Page 448



connected".. This message appears even though the navigation module (A2/30) is correctly locked in the bracket (A2/30-1) in the glove box.



Cause:



1.) Software in navigation module (A2/30).



2.) The tightening torque of the threaded connection between the bracket (A2/30-1) and the glove box is too high. This leads to mechanical stress



between the bracket (A2/30-1) and the navigation module (A2/30).



3.) The LVDS (low voltage differential signal) line is not correctly plugged into the radio (A2).



Note on 3.):



- In vehicles up to and including model year 2012 (code 802), no fault code is logged in the radio (A2); the connector color is blue.



- In vehicles as of model year 2013 (code 803), the fault code 953B is logged in the radio (A2); the connector color is green.



Mercedes-Benz A220 2020 Page 449



Attachments



Remedy:



1.) Perform the following software updates in the navigation module (A2/30):



a) Update interface software (Automotive Software) in navigation module (A2/30) to version 12/21.00 (A 166 902 73 04) (available as of



XENTRY Diagnostics Release 09/12) or higher using XENTRY Diagnostics.



b) Update firmware in navigation module (A2/30) to version R22.3.1205 (available since Week 37/12) or higher using Becker Content Manager.



c) Update navigation software (PND software) in navigation module (A2/30) to version 2.0.50 (available since Week 37/12) or higher using



Becker Content Manager.



Note:



The updates of the navigation software (PND software) including firmware must be performed using the current Becker Content Manager. The



checks for updates on launching the Becker Content Manager must be activated in the "Settings" menu (see attachment). To update the



navigation software, it may be necessary to perform a free-of-charge update of the map data at the same time. Detailed information can be found



at www.beckermappilot.com. The update process can take up to several hours depending on your Internet connection.



2.) Remove bracket (A2/30-1) and reinstall without stress (see attachment):



Note:



The maximum permissible torque is



- 1.7 Nm for models 172 and 204.0, 204.2 and 204.3,



- 2.5 Nm for models 117, 166, 176, 204.9, 207, 212, 218, 242, and 246.



3.) In vehicles up to and including model year 2012 (code 802) and in vehicles as of model year 2013 with fault code 953B remove the radio (A2)



and check the LVDS (low voltage differential signal) line for correct engagement (see attachment).



Mercedes-Benz A220 2020 Page 450



Mercedes-Benz A220 2020 Page 451



Attachments



Symptoms



Control unit/fault code

No comments:

Post a Comment