Skip to main content

version/SCN coded.2017 Mercedes Benz C 43 AMG Diagnostic and Repair# P-88_50-34 Date: 031021

奔驰在1993年推出了底盘编号为w202的紧凑级车型,这也就是大家后来

Body - Trunk Lid Won't Stay Open
Date: October 21, 2003
Order No.: P-B-88.50/34
Supersedes:
Group: 88
SUBJECT:
Model 202.022/023/024/028/029/033
Trunk Lid Does Not Stay Open
If you receive customer reports in the above models regarding the trunk lid not staying open, check to see if the retaining bracket for the tension
spring at the trunk lid hinge is damaged / broken. In this case, the trunk lid hinge bracket must be replaced. It is no longer necessary to replace the
trunk lid hinge since the bracket is available separately.

  1. Remove trim panels on the left and right sides of the trunk.

  2. Install support tool, W170 589 04 63 00, to hold trunk lid securely open.

  3. Remove left and right trunk lid tension springs (Figure 1, 1).

  4. Cut off left and right retaining bracket (Figure 1, 2) at line as indicated in picture with a body saw.

  5. Deburr and break sawed edges.

  6. Enlarge hole (Figure 1, 3) to 6.1 mm diameter.

  7. Prime bare metal in area of repair with primer touch up stick, A000 986 06 50.

  8. Fasten repair brackets (Figure 1, 4). Note installation position on both left and right sides.

  9. Install trunk lid tension springs on left and right sides.


10. Check trunk lid for proper function.
11. Install trim panels on the left and right sides of the trunk.
Mercedes Benz C 43 AMG (202.033) V8-4.3L (113.944) Page 230
Parts Information

Comments

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138, Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...