Wednesday, December 26, 2018

Engine - Failsafe/Codes FC 3100/FC 30FE/FC 30FF Stored

2010 BMW 335Cic Convertible (E93) L6-3.0L Turbo (N54) Technical Service Bulletin # 122807 Date: 110801



Engine - Failsafe/Codes FC 3100/FC 30FE/FC 30FF Stored



SI B12 28 07



Engine Electrical Systems



August 2011



Technical Service



This Service Information bulletin supersedes SI B12 28 07 dated November 2009.



[NEW] designates changes to this revision



SUBJECT



N54 Engine Failsafe: FC 3100, FC 3OFE and/or FC 30FF Is Stored in DME Fault Memory



MODEL



E82 and E88 (1 Series) All models with N54 engine



E90, E92 and E93 (3 Series) All models with N54 engine



E60 and E61 (5 Series) All models with N54 engine



E71 X6 xDrive35i



2010 BMW 335Cic Convertible (E93) L6-3.0L Turbo (N54) 136



INFORMATION



The customer complains that the engine management system has entered the engine failsafe mode and that the turbocharger boost is reduced. One or



both of the following faults are stored in the DME memory:



^ 3100 Boost-pressure control, deactivation - Boost-pressure buildup prohibited



^ 30FE Turbocharger, charge-air pressure too high



^ 30FF Turbocharger, charge-air pressure too low - Charge-air pressure too low.



Note:



If a defective high pressure fuel pump or additional faults are found in the DME memory (e.g., fuel pressure, crank sensor, cam sensor, knock sensor,



etc.), then those faults will be the primary focus of the diagnosis, using the test plans provided for those faults. FC 3100 is only a result of the



component fault.



If FC 3100, 30FE, and/or 30FF are the only faults stored in the memory, then those faults must be the primary focus of the troubleshooting. These



faults are stored due to an incorrect turbocharger boost level, possibly caused by one of the following items:



Troubleshooting Hints:



^ Air path disruption caused by an aftermarket air filter, air filter housing, induction tubes, pop-off (blow-off) valves, exhaust systems, performance



catalytic convertors, increased turbocharger boost caused by "piggy back modules", or tuner software, etc. Refer to B12 10 08 and B12 20 08 for



more details.



^ Leaks or restrictions in the induction system, loose clamps, cracked pipes, or housings. First determine whether the vehicle has a condition where



the induction system could be leaking. What are the adaptation values? Are they positive or negative values? In cases where the adaptations



indicate a lean condition (positive value), a smoke machine is a helpful tool in determining whether the induction system has a leak.



IMPORTANT NOTE:



The VACUTEC(R) Smoke Machine 625-522B-BMW can be purchased via the BMW Equipment Program. Orders for the new machine can be



placed by calling. Included with the new VACUTEC(R) smoke machine are various caps and adaptors to help connect the applicator hose to the



vehicle. It is always suggested to not disturb the system before testing; try to disturb the system as little as possible when connecting the smoke



machine. This smoke machine utilizes an UltraTraceUV(R) smoke solution. The smoke solution incorporates an ultraviolet dye, which helps



pinpoint the leak with an ultraviolet residue surrounding the leak area. Determining the source of the leak is made easy when the included Hi-Density



True UV LED light is used. In the case of the N54 engine, it would be helpful to use the sealing plugs found in the Turbocharger Diagnostic Tool



P/N 81 29 0 426 464 kit.



Note:



The smoke machine hose must be adapted to the sealing plug with another small piece of rubber hose with an approximate outside diameter of



7-8mm.



^ Leaks or restrictions in the exhaust system; visual inspection; and/or use of the smoke machine as described above is helpful. Especially important



when the catalyst conversion faults (29F4/29F5) are stored in conjunction with 3100/30FF.



^ Performing a quick inspection of all vacuum hoses is very important; a slightly collapsed vacuum hose could lead to intermittent boost faults, or



boost faults occurring only under heavy acceleration demands.



2010 BMW 335Cic Convertible (E93) L6-3.0L Turbo (N54) 137



^ Using a vacuum gauge and boost gauge can be very helpful in diagnosing a vehicle with intermittent boost faults. Although the problem may not



be present long enough to set a boost fault, the gauges may show a hint of a deteriorating boost level that could ultimately lead to an effective



repair. Connecting the vacuum gauge at the vacuum actuator on one or both banks (using two gauges) with a "tee" connection will determine the



integrity of the vacuum supply (compare values to the attachment). It is important to block the vacuum bridge located between the two vacuum



solenoids to isolate the vacuum control for each bank. If one solenoid or vacuum hose leading to a solenoid is defective, the system will still



operate with this bridge intact. Removing this bridge may cause the fault to reoccur more frequently if the vacuum control is compromised. Erratic



operation of the vacuum gauge is a hint that a control problem is present; comparing the gauge movement to the other bank or another vehicle will



help determine whether a problem is present.



^ Connecting a boost gauge at one of the two pop-off (blow off) valve's vacuum supply lines can be very effective in measuring boost. Both pop-off



valves must stay in operation during testing; use a vacuum "T" fitting to connect a boost gauge. Attached to this bulletin is a vacuum and boost



specification chart that can be used to troubleshoot the system while driving.



^ Isolating or disconnecting the vacuum supply to the exhaust flap may also eliminate a leakage or a defective vacuum solenoid. This can done very



easily by blocking the hose located near the right front strut tower.



^ Checking the operation of the pop-off (blow-off) valves.



1. Visually inspect the vacuum hose from the intake manifold to both pop-off valves for leaks, restrictions, etc..



2. Remove the pop-off valves.



2010 BMW 335Cic Convertible (E93) L6-3.0L Turbo (N54) 138



3. To check function of the pop-off valves, it is necessary to activate them with vacuum. Turbocharger Diagnostic Tool P/N 81 29 0 426 464 should



be used to supply the 500 mbar of vacuum.



4. The pop-off valve plunger should move to the fully open position and maintain this position when the 500 mbar of vacuum are applied. If the



plunger does not react properly~ the valve must be replaced.



^ The Turbocharger Diagnostic Tool P/N 81 29 0 426 464 can only be operated in conjunction with the DIS Plus or GT1 with MIB. Refer to SI



B04 04 07 (Turbo Diagnostic Tool) and Repair Instruction RA 11 61 730 (Checking diagnosis unit for overpressure and vacuum pressure) for



additional details.



^ If the turbochargers are removed from the vehicle for inspection, it is necessary to inspect the actuator and waste gate wear, using the



measurement described in Repair Instruction RA 11 65 580 Replacing vacuum unit (wastegate valve)(N54).



^ Do not replace the turbochargers. This replacement requires a TeileClearing PuMA case. In some cases, TC may require additional measurements



and photos to describe the suspected problem.



[NEW] WARRANTY INFORMATION



ATTACHMENT



2010 BMW 335Cic Convertible (E93) L6-3.0L Turbo (N54) 139



2010 BMW 335Cic Convertible (E93) L6-3.0L Turbo (N54) 140



B122807 Vacuum And Boost Valves



2010 BMW 335Cic Convertible (E93) L6-3.0L Turbo (N54) 141

No comments:

Post a Comment