Skip to main content

Computers/Controls - Feature Customization


Computers/Controls - Feature Customization



SI M 09 01 02



Programming/Coding Explanations



December 2005



Technical Service



This Service Information bulletin supersedes S.I. M09 01 02 dated August 2005.



[NEW] designates changes to this revision



SUBJECT



Vehicle Memory



MODEL



R50 (Cooper), R52 (Convertible), R53 (Cooper S)



2002-2006 Mini Cooper (R50) L4-1.6L (W10) Page 131



2002-2006 Mini Cooper (R50) L4-1.6L (W10) Page 132



SITUATION



Various operating features in MINI vehicles may be customized using Vehicle Memory. There are different settings available for MINI vehicles of



different model years (see attachment).



All Sales and Service personnel should be aware that Vehicle Memory can be set with either DISPLus or GT1 because recent customer surveys



indicate a customer demand for such adjustments.



Note:



No separate Key Memory is available for MINI



PROCEDURE



2002-2006 Mini Cooper (R50) L4-1.6L (W10) Page 133



The customer must be informed about possible choices before delivery by filling out a selection sheet (a printable version is included). One copy of



the questionnaire stays with the customer, one copy goes to



sales department, and one copy to service department. According to the customer choices, the vehicle should be customized during the QC 1.



Selection changes during the ownership period are not reimbursable under warranty. The customer should not be charged for the programming.



Individualizing your customer's vehicle is an important contribution to a positive customer experience.



Note:



Any additional items contained in the table of all available options (attached) may also be programmed, but we recommend that they should be



discussed with customers at later date during a service consultation or upon customer request.



Using DISplus/GT1, select Coding/Vehicle Memory to access the Vehicle Memory program:



1. After a short period of time the menu screen will be displayed with a list of all detected control systems capable of Vehicle Memory



configuration.



2. Using the owner's selection list, enter the system selected for customization.



3. From the system submenu select the function to be altered.



4. Make the appropriate selection (activation/deactivation). The following symbols may be displayed next to the selection choice:



2002-2006 Mini Cooper (R50) L4-1.6L (W10) Page 134



"=" - sign indicates present status



"*" - sign indicates factory default (when present vehicle selection is different)



">" - sign indicates entered change in selection



5. After pressing the "continue" arrow, the system will accept the change in selection and the VEHICLE MEMORY main menu will be



displayed. If additional changes are required, enter the appropriate system and repeat steps from above.



6. When all of the required VEHICLE MEMORY configuration changes are entered, scroll down to the bottom of the main menu.



7. Select "SET VEHICLE" and follow the on-screen instructions to complete the coding process.



Select "Car Memory", then "Print List" to record the new settings. Place the print list in the vehicle service file for future reference.



[NEW] Vehicle Memory using CIP V20.0 or later:



1. If SSS is used to control the Programming Session directly, continue with step 4.



2. If remote functionality of GT1 is used to control the Programming Session, select "Coding/Programming"



3. Select an available SSS in the network.



4. Press "New Session" on the Program Homepage screen to start CIP.



5. Select the appropriate vehicle model.



6. Press the "CKM" button at the screen with the text "Program SELECTION: Load software, Car & Key Memory (CKM)".



7. The CKM screen displays all available CKM functions, their current settings, and the factory default setting.&line;Note: When selecting the



text of each functionality, a popup screen will show further information about the selection.



8. Make CKM selections according to the customer request.



9. Press "Encode Car"



10. Press "Save", and a screen is displayed with green check marks to confirm that the VKM selections have programmed correctly.



11. Press "Finish" to return to the selection screen, with the new selections marked accordingly.



Important:



Observe the battery voltage level during the configuration. A low voltage condition will terminate the process or will incorrectly configure the

Comments

Popular posts from this blog

2010 Mercedes Benz C 300 4MATIC (204.081) V6-3.0L (272.948) A L L Diagnostic Trouble Codes ( DTC ): P Code Charts P1240

2010 Mercedes Benz C 300 4MATIC (204.081) V6-3.0L (272.948)     A L L  Diagnostic Trouble Codes ( DTC ): P Code Charts P1240 The CAN bus is malfunctioning.   Test 1: Check the CAN communication with control unit Engine control module.   Test 2: Possible cause: - Drive train CAN bus Affected functions: - Engine diagnosis - Fuel system 1. Check the CAN communication with control unit Engine control module. Important note A CAN timeout fault code is set due to the absence of a CAN input signal.The cause of this may be not only the transmitter control unit, but also the CAN networking.Possible cause and remedy - Check CAN communication with affected control unit. - Check other control units for vehicle CAN bus failure in the stored faults. - CAN bus has loose contact or Open circuit. Continue with button F 2 Warning!Communication with ECU required. 2. No further information available.

2019 Mercedes-Benz X-Class

Launched for the brand new 3-Series coupe and convertible and provided on all engine variants, M Sport cars include a raft of extra equipment as standard compared to an SE model. Furthermore, passive safety is offered thanks to standard tools akin to seven airbags and the i-Size attachment system for 2 little one seats. Standard safety gear includes antilock disc brakes, stability and traction management, aspect airbags, side curtain airbags, knee airbags and Mercedes-Benz's "mbrace" emergency telematics system. The SLS is supposed to be Mercedes-Benz's ultimate vehicle, however it is also meant to be extra affordable and sensible to drive than the now-discontinued Mercedes SLR McLaren. Twelve (more than one-third) of the above differences are in the double digits. Although the price is affordable or not, are the primary disadvantages of space and rear seats for Mercedes-Benz C-Class 220 CDI vibration motor in the city. In case your body kit includes entrance and/or r...

Mercedes Benz C 300 4MATIC # LI80-57_P-051521 Date: 110601 30 Steering/Starting - No Crank/Start/ESL And ICM Don't Respond No Crank/No Start/ESL and ICM do not respond to key input

 Mercedes Benz C 300 4MATIC # LI80-57_P-051521 Date: 110601   30 Steering/Starting - No Crank/Start/ESL And ICM Don't Respond No Crank/No Start/ESL and ICM do not respond to key input Topic number LI80.57-P-051521 Version 1 Design group 80.57 Drive authorization systems (DAS) Date 06-01-2011 Validity All 204, 207 model vehicles Reason for change Complaint 1. No crank / no start / intermittent no crank 2. Communication via SDS to Electronic Ignition Switch N73 (EIS/EZS), and or short test may or may not be possible at time of fault 3. Below scenario: ^ When accessing the occupants compartment, the message center in the ICM will illuminate (note: eventually the message center will time out and shut down, and will not illuminate until the CAN is activated via the interior lock/unlock switch). ^ The key will turn in EIS N73. ^ The ESL N26/5 does not activate/respond (or the steering wheel remains unlocked at all times). ^ The warning icons in the ICM will not il...

2010 Mercedes Benz C 300 (204.054) V6-3.0L (272.947) Page 2499

2.1.3.2.1.4. Check power supply at control unit N15/3 (ETC [EGS] control unit). Test 2.1.3.2.1.4.1: Guided test 2.1.3.2.1.4.1. Guided test Operation number of operation texts and work units or standard texts and flat rates:27-0641Possible cause - Battery has incorrect charge state or is faulty. - Local undervoltage of component N15/3 (ETC [EGS] control unit) Test sequence - Erase fault memory. Continue with button "F2" Warning!Communication with ECU required. 2.1.3.2.1.5. Check power supply at control unit N15/5 (Electronic selector lever module control unit). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test sequence - Switch off ignition. - Disconnect connector at component N15/5 (Electronic selector lever module control unit). - Switch on ignition. - [A.2] Measure direct voltage with multimeter between 2 and 1 [A.1] Status of relevant actual value: - Supply voltage (tml. 15):Warning! Communication with ECU required. Specified ...

2010 Cadillac Truck SRX AWD V6-3.0L Page 1240

2010 Cadillac Truck SRX AWD V6-3.0L Page 1240 Diagnosis (Without Special Tool) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests and General Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (Without Special Tool)). * Missing, restricted, or leaking exhaust components-Refer to Symptoms - Engine Exhaust (See: Engine, Cooling and Exhaust/Exhaust System/Testing and Inspection/Symptoms - Engine Exhaust). * Malfunctioning fuel injectors-Refer to Fuel Injector Solenoid Coil Test (LAU) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection)Fuel Injector Solenoid Coil Test (LF1, LFW) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection). * Vacuum hoses for splits, kinks, and improper connections * Insufficient fuel in the tank * Low fuel pressure-Refer to Fuel System Diagnosis (LF1 China) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Test...

Check the CAN communication with control unit N80 (Steering column module). Interior CAN bus

Part 1 One or more messages from control unit N80 (Steering column module) are not available on the CAN bus. Possible cause: Check the CAN communication with control unit N80 (Steering column module). Interior CAN bus Affected functions: CAN Communication Automatic transmission Function ------------------------------------------------- Test 1: Engine compartment CAN test Test 2: Check the CAN communication with control unit N80 (Steering column module). Test 3: Interior CAN check Engine compartment CAN test Test 1.1: Procedure in case of CAN faults Test 1.2: Evaluation of CAN fault codes Test 1.3: Further CAN test options Procedure in case of CAN faults Test 1.1.1: How do I quickly reach my goal? Test 1.1.2: General test information Test 1.1.3: General CAN fundamentals Test 1.1.4: Possible aids and their usage How do I quickly reach my goal? How do I quickly reach my goal?First call up menu item 'Evaluation of CAN...

Relay 'Circuit 87' ( Engine ) (P2505)

P2505 Relay 'Circuit 87' ( Engine ) (P2505) Possible cause: ­ N3/10 (ME­SFI [ME] control unit) ­ K40/4kK (Engine electronics and chassis relay) Affected functions: ­ Battery / On­board electrical system ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Check power supply of component N3/10 (ME­SFI [ME] control unit). Test 2: Arrangement of fuses Page 2562010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 257 1. Check power supply of component N3/10 (ME­SFI [ME] control unit). Test 1.1: Test voltage supply of circuit 87. 1.1. Test voltage supply of circuit 87. Figure legend ­ A ­ConnectionTest cable 35­pin socket box ­ 001 ­Sockets of component N3/10 (ME­SFI [ME] control unit) ­ 05 ­35­pin socket box ­ 050 ­126­pin socket box ­ 108 ­Test cable 266 589 01 63 00 ­ N3/10 (ME­SFI [ME] control unit) ­ II 1­63ConnectionTest cable ­ III 64­126ConnectionTest cable Warning! ­ ­ Connection A of test ca...

A/T - ECO Start/Stop Inoperative, DTC P0944 Stored In TCM ECO start/stop inoperative, fault code P0944 in transmission control unit

Mercedes-Benz Mercedes Benz OEM Parts Mercedes Benz OE Replacement Parts Technical Service Bulletin # LI27-57_P-0534962 Date: 120522 2010 Mercedes Benz SL 550 (230.471) V8-5.5L (273.965)   Page 29 A/T - ECO Start/Stop Inoperative, DTC P0944 Stored In TCM ECO start/stop inoperative, fault code P0944 in transmission control unit Topic number LI27.57-P-053496 Version 2 Design group 27.57 Oil pump Date 05-22-2012 Validity NAG2 FEPlus (722.9) with auxiliary oil pump with code B03 up to transmission sequence number 7.248.200 Reason for change Model series 251 deleted because model series 251 does not have ECO start/stop. Complaint: ECO start/stop inoperative, fault code P0944 in transmission control unit. Attachments Cause: Check valve in torque converter housing may be damaged. Leakage between torque converter housing and auxiliary oil pump. May affect transmissions with transmission sequence numbers starting with -07-xxx xxx. Remedy: Access v...

Mercedes Benz SLK 55 AMG No CAN message was received from control unit Engine management.

2010 Mercedes Benz SLK 55 AMG (171.473) V8-5.5L (113.989) Copyright ? 2013, ALLDATA 10.52SS Page 1 A L L Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts Part 1 No CAN message was received from control unit Engine management. Possible cause: - Fault in CAN communication with control unit Motor electronics. - Drive train CAN bus Affected functions: - CAN Communication - Automatic transmission Function ------------------------------------------------- Test 1: Engine compartment CAN test Test 2: Check the CAN communication with control unit Engine management. Test 3: Drive train CAN test 1. Engine compartment CAN test Test 1.1: Procedure in case of CAN faults Test 1.2: Evaluation of CAN fault codes Test 1.3: Further CAN test options 1.1. Procedure in case of CAN faults Test 1.1.1: How do I quickly reach my goal? Test 1.1.2: General test information Test 1.1.3: General CAN fundamentals Test 1.1.4: Possible aids and their usage 1.1.1. How do I quickly reach...