Skip to main content

Mercedes Benz E 550 4MATIC Sedan Technical Service Bulletin # LI54-18_P-048131 Date: 091120


 Mercedes Benz E 550 4MATIC Sedan Technical Service Bulletin # LI54-18_P-048131 Date: 091120
Computer Controls/Electrical - Various Malfunctions/DTCs
WIRING HARNESS IS DAMAGED IN AREA OF ROOF FRAME
Topic number LI54.18-P-048131
Version 1
Design group 54.18 Cable harnesses
Date 11-20-2009
Validity BR 212 USA vehicles up to VIN end number A039612
Reason for change
Reason for block
Complaint:
List of possible Complaints:
1.)See Remedy #1
- Vehicle cannot be started because the chassis CAN bus and/or interior CAN bus is faulty, CAN fault codes stored in quick test.
- Interior CAN bus malfunction or "Bus off"
- Overhead control panel nonfunctional
2.)See Remedy #2
- Bluetooth nonfunctional
3.)See Remedy #3
- Chassis CAN bus malfunction or "Bus off"
- Multifunction camera nonfunctional or malfunctions
4.)See Remedy #4
2010 Mercedes Benz E 550 4MATIC Sedan (212.090) V8-5.5L (273.970)   Page 180
- Night View Camera nonfunctional or malfunctions
Attachments
Cause:
Wiring harness may be touching absorbers (see attachment no. 1) or jammed and thus damaged in the area of the roof frame at the transition to the
left front or right front A-pillar.
Individual lines may be pinched behind the absorber (see attachment no. 2).
Cable strand may be touching the edge of the absorber and individual lines may thus be chafed (see attachment no. 3).
Attachments
Remedy:
List of Remedies:
1.) Remedy #1: Overhead control panel nonfunctional or interior CAN bus malfunction or "Bus off":
Check wiring harness in area of roof frame at transition to left front A-pillar.
Remove left front sun visor.
Remove left front grab handle.
Lower left front headliner.
Check wiring harness for damage in area of absorber (see attachment no. 1).
If the power supply lines or CAN lines are damaged, repair the lines with the familiar wiring harness repair methods (AR00.19-P-0100A).
2.)Remedy #2: Bluetooth nonfunctional
Check wiring harness in area of roof frame at transition to left front A-pillar.
Remove left front sun visor.
Remove left front grab handle.
Lower left front headliner.
Check wiring harness for damage in area of absorber (see attachment no. 1).
If the Bluetooth antenna is damaged, replace the Bluetooth antenna.
3.)Remedy #3: Failure or malfunction of multifunction camera or chassis CAN bus malfunction or "Bus off"
Check wiring harness in area of roof frame at transition to right front A-pillar.
Remove right front sun visor.
Remove right front grab handle.
2010 Mercedes Benz E 550 4MATIC Sedan (212.090) V8-5.5L (273.970)   Page 181
Lower right front headliner.
Check wiring harness for damage in area of absorber (see attachment no. 1).
If the power supply lines or CAN lines are damaged, repair the lines with the familiar wiring harness repair methods (AR00.19-P-0100A).
4.)Remedy #4: Night View Camera nonfunctional or malfunctions.
Check wiring harness in area of roof frame at transition to right front A-pillar.
Remove right front sun visor.
Remove right front grab handle.
Lower right front headliner.
Check wiring harness for damage in area of absorber (see attachment no. 1).
If the LVDS cable of the Night View camera is damaged, replace the LVDS cable.
After completing the required repairs, ensure that the line routing is correct.
The cable strand must run between the absorber and roof frame (see attachment no. 1).
Fix the cable strand to the roof frame with felt so that the cable strand cannot slide onto the edge of the absorber.
Symptoms
2010 Mercedes Benz E 550 4MATIC Sedan (212.090) V8-5.5L (273.970)   Page 182
Control unit/fault code
Parts
Work units
2010 Mercedes Benz E 550 4MATIC Sedan (212.090) V8-5.5L (273.970)   Page 183
Validity
Attachment 1 - Insulation
2010 Mercedes Benz E 550 4MATIC Sedan (212.090) V8-5.5L (273.970)   Page 184
Attachment 2 - Wiring harness pinched at absorber
2010 Mercedes Benz E 550 4MATIC Sedan (212.090) V8-5.5L (273.970)   Page 185
Attachment 3 - Wiring harness touches edge of absorber

Popular posts from this blog

2010 Mercedes Benz C 300 4MATIC (204.081) V6-3.0L (272.948) A L L Diagnostic Trouble Codes ( DTC ): P Code Charts P1240

2010 Mercedes Benz C 300 4MATIC (204.081) V6-3.0L (272.948)     A L L  Diagnostic Trouble Codes ( DTC ): P Code Charts P1240 The CAN bus is malfunctioning.   Test 1: Check the CAN communication with control unit Engine control module.   Test 2: Possible cause: - Drive train CAN bus Affected functions: - Engine diagnosis - Fuel system 1. Check the CAN communication with control unit Engine control module. Important note A CAN timeout fault code is set due to the absence of a CAN input signal.The cause of this may be not only the transmitter control unit, but also the CAN networking.Possible cause and remedy - Check CAN communication with affected control unit. - Check other control units for vehicle CAN bus failure in the stored faults. - CAN bus has loose contact or Open circuit. Continue with button F 2 Warning!Communication with ECU required. 2. No further information available.

2019 Mercedes-Benz X-Class

Launched for the brand new 3-Series coupe and convertible and provided on all engine variants, M Sport cars include a raft of extra equipment as standard compared to an SE model. Furthermore, passive safety is offered thanks to standard tools akin to seven airbags and the i-Size attachment system for 2 little one seats. Standard safety gear includes antilock disc brakes, stability and traction management, aspect airbags, side curtain airbags, knee airbags and Mercedes-Benz's "mbrace" emergency telematics system. The SLS is supposed to be Mercedes-Benz's ultimate vehicle, however it is also meant to be extra affordable and sensible to drive than the now-discontinued Mercedes SLR McLaren. Twelve (more than one-third) of the above differences are in the double digits. Although the price is affordable or not, are the primary disadvantages of space and rear seats for Mercedes-Benz C-Class 220 CDI vibration motor in the city. In case your body kit includes entrance and/or r...

Mercedes Benz C 300 4MATIC # LI80-57_P-051521 Date: 110601 30 Steering/Starting - No Crank/Start/ESL And ICM Don't Respond No Crank/No Start/ESL and ICM do not respond to key input

 Mercedes Benz C 300 4MATIC # LI80-57_P-051521 Date: 110601   30 Steering/Starting - No Crank/Start/ESL And ICM Don't Respond No Crank/No Start/ESL and ICM do not respond to key input Topic number LI80.57-P-051521 Version 1 Design group 80.57 Drive authorization systems (DAS) Date 06-01-2011 Validity All 204, 207 model vehicles Reason for change Complaint 1. No crank / no start / intermittent no crank 2. Communication via SDS to Electronic Ignition Switch N73 (EIS/EZS), and or short test may or may not be possible at time of fault 3. Below scenario: ^ When accessing the occupants compartment, the message center in the ICM will illuminate (note: eventually the message center will time out and shut down, and will not illuminate until the CAN is activated via the interior lock/unlock switch). ^ The key will turn in EIS N73. ^ The ESL N26/5 does not activate/respond (or the steering wheel remains unlocked at all times). ^ The warning icons in the ICM will not il...

2010 Mercedes Benz C 300 (204.054) V6-3.0L (272.947) Page 2499

2.1.3.2.1.4. Check power supply at control unit N15/3 (ETC [EGS] control unit). Test 2.1.3.2.1.4.1: Guided test 2.1.3.2.1.4.1. Guided test Operation number of operation texts and work units or standard texts and flat rates:27-0641Possible cause - Battery has incorrect charge state or is faulty. - Local undervoltage of component N15/3 (ETC [EGS] control unit) Test sequence - Erase fault memory. Continue with button "F2" Warning!Communication with ECU required. 2.1.3.2.1.5. Check power supply at control unit N15/5 (Electronic selector lever module control unit). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test sequence - Switch off ignition. - Disconnect connector at component N15/5 (Electronic selector lever module control unit). - Switch on ignition. - [A.2] Measure direct voltage with multimeter between 2 and 1 [A.1] Status of relevant actual value: - Supply voltage (tml. 15):Warning! Communication with ECU required. Specified ...

2010 Cadillac Truck SRX AWD V6-3.0L Page 1240

2010 Cadillac Truck SRX AWD V6-3.0L Page 1240 Diagnosis (Without Special Tool) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests and General Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (Without Special Tool)). * Missing, restricted, or leaking exhaust components-Refer to Symptoms - Engine Exhaust (See: Engine, Cooling and Exhaust/Exhaust System/Testing and Inspection/Symptoms - Engine Exhaust). * Malfunctioning fuel injectors-Refer to Fuel Injector Solenoid Coil Test (LAU) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection)Fuel Injector Solenoid Coil Test (LF1, LFW) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection). * Vacuum hoses for splits, kinks, and improper connections * Insufficient fuel in the tank * Low fuel pressure-Refer to Fuel System Diagnosis (LF1 China) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Test...

Check the CAN communication with control unit N80 (Steering column module). Interior CAN bus

Part 1 One or more messages from control unit N80 (Steering column module) are not available on the CAN bus. Possible cause: Check the CAN communication with control unit N80 (Steering column module). Interior CAN bus Affected functions: CAN Communication Automatic transmission Function ------------------------------------------------- Test 1: Engine compartment CAN test Test 2: Check the CAN communication with control unit N80 (Steering column module). Test 3: Interior CAN check Engine compartment CAN test Test 1.1: Procedure in case of CAN faults Test 1.2: Evaluation of CAN fault codes Test 1.3: Further CAN test options Procedure in case of CAN faults Test 1.1.1: How do I quickly reach my goal? Test 1.1.2: General test information Test 1.1.3: General CAN fundamentals Test 1.1.4: Possible aids and their usage How do I quickly reach my goal? How do I quickly reach my goal?First call up menu item 'Evaluation of CAN...

Relay 'Circuit 87' ( Engine ) (P2505)

P2505 Relay 'Circuit 87' ( Engine ) (P2505) Possible cause: ­ N3/10 (ME­SFI [ME] control unit) ­ K40/4kK (Engine electronics and chassis relay) Affected functions: ­ Battery / On­board electrical system ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Check power supply of component N3/10 (ME­SFI [ME] control unit). Test 2: Arrangement of fuses Page 2562010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 257 1. Check power supply of component N3/10 (ME­SFI [ME] control unit). Test 1.1: Test voltage supply of circuit 87. 1.1. Test voltage supply of circuit 87. Figure legend ­ A ­ConnectionTest cable 35­pin socket box ­ 001 ­Sockets of component N3/10 (ME­SFI [ME] control unit) ­ 05 ­35­pin socket box ­ 050 ­126­pin socket box ­ 108 ­Test cable 266 589 01 63 00 ­ N3/10 (ME­SFI [ME] control unit) ­ II 1­63ConnectionTest cable ­ III 64­126ConnectionTest cable Warning! ­ ­ Connection A of test ca...

A/T - ECO Start/Stop Inoperative, DTC P0944 Stored In TCM ECO start/stop inoperative, fault code P0944 in transmission control unit

Mercedes-Benz Mercedes Benz OEM Parts Mercedes Benz OE Replacement Parts Technical Service Bulletin # LI27-57_P-0534962 Date: 120522 2010 Mercedes Benz SL 550 (230.471) V8-5.5L (273.965)   Page 29 A/T - ECO Start/Stop Inoperative, DTC P0944 Stored In TCM ECO start/stop inoperative, fault code P0944 in transmission control unit Topic number LI27.57-P-053496 Version 2 Design group 27.57 Oil pump Date 05-22-2012 Validity NAG2 FEPlus (722.9) with auxiliary oil pump with code B03 up to transmission sequence number 7.248.200 Reason for change Model series 251 deleted because model series 251 does not have ECO start/stop. Complaint: ECO start/stop inoperative, fault code P0944 in transmission control unit. Attachments Cause: Check valve in torque converter housing may be damaged. Leakage between torque converter housing and auxiliary oil pump. May affect transmissions with transmission sequence numbers starting with -07-xxx xxx. Remedy: Access v...

Mercedes Benz SLK 55 AMG No CAN message was received from control unit Engine management.

2010 Mercedes Benz SLK 55 AMG (171.473) V8-5.5L (113.989) Copyright ? 2013, ALLDATA 10.52SS Page 1 A L L Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts Part 1 No CAN message was received from control unit Engine management. Possible cause: - Fault in CAN communication with control unit Motor electronics. - Drive train CAN bus Affected functions: - CAN Communication - Automatic transmission Function ------------------------------------------------- Test 1: Engine compartment CAN test Test 2: Check the CAN communication with control unit Engine management. Test 3: Drive train CAN test 1. Engine compartment CAN test Test 1.1: Procedure in case of CAN faults Test 1.2: Evaluation of CAN fault codes Test 1.3: Further CAN test options 1.1. Procedure in case of CAN faults Test 1.1.1: How do I quickly reach my goal? Test 1.1.2: General test information Test 1.1.3: General CAN fundamentals Test 1.1.4: Possible aids and their usage 1.1.1. How do I quickly reach...