Skip to main content

M16/4 (Rear throttle valve actuator) : Actual value potentiometer 1 or 2 has failed. (P0225)

P0225
M16/4 (Rear throttle valve actuator) : Actual value potentiometer 1 or 2 has failed. (P0225)
Possible cause:
­ M16/4 (Rear throttle valve actuator)
Affected functions:
­
­
Engine diagnosis
Engine output
­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­
Test 1: Check component M16/4 (Rear throttle valve actuator).
1. Check component M16/4 (Rear throttle valve actuator).
Test 1.1: Check component M16/4 (Rear throttle valve actuator) using actual value.
Test 1.2: Check component M16/4 (Rear throttle valve actuator) by means of actuation.
Test 1.3: Check internal resistance of component M16/4m1 (Actuator motor).
Test 1.4: Test voltage supply of the potentiometers of component M16/4 (Rear throttle valve actuator).
1.1. Check component M16/4 (Rear throttle valve actuator) using actual value.
Test prerequisite
­ Switch ignition on and wait at least for 60 s.
­ Engine not running
Status of the relevant actual values:
­ M16/4 (Rear throttle valve actuator) : Voltage 1: Warning! Communication with ECU required.
­ M16/4 (Rear throttle valve actuator) : Voltage 2: Warning! Communication with ECU required.
Specified values
­ M16/4 (Rear throttle valve actuator)Signal 1(Accelerator not operated): [0.30...1.00] V
­ M16/4 (Rear throttle valve actuator)Signal 2(Accelerator not operated): [3.90...4.60] V
­ M16/4 (Rear throttle valve actuator)Signal 1(Kickdown switch operated, accelerator fully depressed):[3.80...4.70] V
­ M16/4 (Rear throttle valve actuator)Signal 2(Kickdown switch operated, accelerator fully depressed):[0.40...1.00] V
Question
­
Are the actual values o.k.?
YES
The actual values are okay.End of test
Page 8532010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985)
Copyright ? 2013, ALLDATA
10.52SS
NO
At least one of the relevant actual values is not okay.Possible cause and remedy
­
Check power supply of component M16/4 (Rear throttle valve actuator).
1.2. Check component M16/4 (Rear throttle valve actuator) by means of actuation.
Test prerequisite
­ Operate engine at idling speed.
Note
­ If the throttle valve angle is< 1,1 ?, unmetered air may be present.
Status of relevant actual value:
­ Throttle valve angle: Warning! Communication with ECU required.
Move on to actuation with button F2
1.3. Check internal resistance of component M16/4m1 (Actuator motor).
Figure legend
­ A ­ConnectionTest cable 35­pin socket box
­ 001 ­Sockets of component N3/10 (ME­SFI [ME] control unit)
­ 05 ­35­pin socket box
­ 050 ­126­pin socket box
­ 108 ­Test cable 266 589 01 63 00
­ N3/10 (ME­SFI [ME] control unit)
­ II 1­63ConnectionTest cable
­ III 64­126ConnectionTest cable
Warning!
­
­
Connection A of test cable 108 may NOT be connected to connection B of the 126­pin socket box (050).
Test sequence
­
­
Switch off ignition.
Connect socket box (126­pin) to component N3/10 (ME­SFI [ME] control unit).
Page 8542010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985)
Copyright ? 2013, ALLDATA
10.52SS
­ Disconnect coupling M at component N3/10 (ME­SFI [ME] control unit).
­ Measure resistance with multimeter between sockets (M.96) 96 and (M.72) 72 of the 126­pole socket box tester.
Specified value
­ Resistor[1...10]ohms
Question
­
Is the measurement value OK?
YES
The measurement value is OK.End of test
NO
The measurement value is not OK.Possible cause and remedy
­ Lines between N3/10 (ME­SFI [ME] control unit) and M16/4m1 (Actuator motor)
­ M16/4m1 (Actuator motor)
End of test
1.4. Test voltage supply of the potentiometers of component M16/4 (Rear throttle valve actuator).
Figure legend
­ A ­ConnectionTest cable 35­pin socket box
­ 001 ­Sockets of component N3/10 (ME­SFI [ME] control unit)
­ 05 ­35­pin socket box
­ 050 ­126­pin socket box
­ 108 ­Test cable 266 589 01 63 00
­ N3/10 (ME­SFI [ME] control unit)
­ II 1­63ConnectionTest cable
­ III 64­126ConnectionTest cable
Warning!
­
­
Connection A of test cable 108 may NOT be connected to connection B of the 126­pin socket box (050).
Test prerequisite
Page 8552010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985)
Copyright ? 2013, ALLDATA
10.52SS
Page 856
­ At least one of the relevant actual values is not okay.
­ The power supply of component N3/10 (ME­SFI [ME] control unit) is OK.
Test sequence
­ Switch off ignition.
­ Connect socket box (126­pin) to component N3/10 (ME­SFI [ME] control unit).
­ Measure direct voltage with multimeter between sockets [M.39] 39 and [M.43] 43 of the 35­pole socket box tester.
­ Switch on ignition.
Specified value
­ Voltage[4.75...5.25] V
Question
­
Is the measurement value OK?
YES
The measurement value is OK.Possible cause and remedy
­ Check lines from component M16/4 (Rear throttle valve actuator) to component N3/10 (ME­SFI [ME] control unit).
End of test
NO
The measurement value is not OK.Possible cause and remedy
­ Test wiring for Short circuit.
­ N3/10 (ME­SFI [ME] control unit)
End of test
Labels:
Location: 24507-24599 561st Ave, Winthrop, MN 55396, USA

Popular posts from this blog

MAX Advanced Brakes Rear Brake Kit Review | Hyundai Elantra, Kia Forte & Soul

MAX Advanced Brakes Rear Brake Kit Review | Hyundai Elantra, Kia Forte & Soul Brake Kit Review MAX Advanced Brakes Rear Brake Kit Review The MAX Advanced Brakes rear brake kit is aimed at drivers who want a simple all-in-one rear brake refresh instead of sourcing pads and rotors separately. Current listings for this exact product pattern describe it as a rear kit for 2011–2020 Hyundai Elantra , 2014–2023 Kia Forte , and 2014–2023 Kia Soul , built around carbon-ceramic brake pads and OE-replacement rear rotors . ([walmart.com](https://www.walmart.com/ip/1423086570?utm_source=openai)) That combination makes sense for buyers focused on regular daily driving rather than track-style braking upgrades. The listings consistently frame this line around “daily driving” and OEM-style replacement rather than aggressive perfo...
Post a Comment
Read more

NOCO GENIUS1: 1A 6V/12V Smart Battery Charger – Automatic Maintainer, Trickle Charger & Desulfator with Overcharge Protection & Temperature Compensation – for Lead-Acid & Lithium Batteries

NOCO GENIUS1 Review: Compact 1A Smart Battery Charger, Maintainer, Trickle Charger, and Desulfator The NOCO GENIUS1 is a compact smart battery charger designed for drivers, motorcycle owners, powersports users, and anyone who wants an easy way to keep batteries healthy during storage or between uses. Marketed as a 1A 6V/12V smart battery charger , it combines several useful functions in one unit: automatic charging, battery maintaining, trickle charging, desulfation support, overcharge protection, and temperature compensation . If you need a charger for lead-acid or lithium batteries and want something more advanced than a basic plug-in charger, the GENIUS1 is built to offer safer long-term maintenance with minimal effort. It is especially appealing for seasonal vehicles, backup batteries, motorcycles, ATVs, lawn equipment, and cars that are not driven every day. What Makes the NOCO GENIUS1 Stand Out? The biggest strength of the NOCO GENIUS1 is that it is not just a simple...
Post a Comment
Read more

D138， Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...
Post a Comment
Read more

4 Pairs Compression Socks for Women & Men Review | 15-20 mmHg Support for Nurses and Running

4 Pairs Compression Socks for Women & Men Review | 15-20 mmHg Support for Nurses and Running Compression Socks Review 4 Pairs Compression Socks for Women & Men Review The 4 Pairs Compression Socks for Women & Men Circulation 15-20 mmHg category is popular for one simple reason: it targets people who spend long hours on their feet, sit for extended periods, travel often, or want a little more lower-leg support during daily life. Products in this exact listing pattern are consistently marketed for nurses , running , travel , and general circulation support. A 15-20 mmHg compression level usually sits in the mild-to-moderate range that many people consider for everyday wear, especially when they want help with leg fatigue, swelling, or long-shift comfort. That is one reason this kind of sock appeals to w...
Post a Comment
Read more

Check the CAN communication with control unit N80 (Steering column module). Interior CAN bus

Part 1 One or more messages from control unit N80 (Steering column module) are not available on the CAN bus. Possible cause: Check the CAN communication with control unit N80 (Steering column module). Interior CAN bus Affected functions: CAN Communication Automatic transmission Function ------------------------------------------------- Test 1: Engine compartment CAN test Test 2: Check the CAN communication with control unit N80 (Steering column module). Test 3: Interior CAN check Engine compartment CAN test Test 1.1: Procedure in case of CAN faults Test 1.2: Evaluation of CAN fault codes Test 1.3: Further CAN test options Procedure in case of CAN faults Test 1.1.1: How do I quickly reach my goal? Test 1.1.2: General test information Test 1.1.3: General CAN fundamentals Test 1.1.4: Possible aids and their usage How do I quickly reach my goal? How do I quickly reach my goal?First call up menu item 'Evaluation of CAN...
Post a Comment
Read more

P179A77 The redundancy system for DIRECT SELECT has a malfunction. The commanded position cannot be reached.

P179A77 The redundancy system for DIRECT SELECT has a malfunction. The commanded position cannot be reached. Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps required to perform a complete initial startup of system ISM.Preconditions ­ The new control unit must have already...
Read more

A L L Diagnostic Trouble Codes ( DTC ): P Code Charts M166 (Throttle valve actuator) : The throttle valve is amming or is stiff. (P2176)

2010 Mercedes Benz C 300 4MATIC (204.081) V6-3.0L (272.948)   A L L  Diagnostic Trouble Codes ( DTC ): P Code Charts M166 (Throttle valve actuator) : The throttle valve is amming or is stiff. (P2176) M166 (Throttle valve actuator) : The throttle valve is amming or is stiff. (P2176) Possible cause: - M16/6 (Throttle valve actuator) Affected functions: - Engine diagnosis - Engine running ------------------------------------------------   Test 1: Check component M16/6 (Throttle valve actuator). 1. Check component M166 (Throttle valve actuator).   Test 1.1: Check component M16/6 (Throttle valve actuator) using actual value.   Test 1.2: Check component M16/6m1 (Actuator motor) by means of actuation.   Test 1.3: Perform mechanical inspection of component M16/6 (Throttle valve actuator).   Test 1.4: Note : Control unit programming must be performed on control unit variants VC6 to VC8. 1.1. Check component M166 (Throttle valve actuator) using ac...
Read more

Engine makes intermittent knocking noise, ticking/crackling

Vehicle: All Technical Service Bulletins Diesel Engine - Crackling/Ticking Noise At Idle Engine makes intermittent knocking noise, ticking/crackling Topic number LI03.20-P-048278 Version 3 Design group 03.20 Crankshaft Date 03-26-2013 Validity Model series 211, 219 with OM 642 Model series 164, 251 with OM 642 Model series 203, 204, 209, 221 461 463 with OM 642 Reason for change New part number for upper main bearing shell, bearing point 1 Complaint: The engine makes ticking/crackling noises at idle speed and at speeds up to approx. 1500 rpm. Notes: ^ The noise occurs after a mileage of approx. 20,000 km or after an oil change. ^ Noise can be clearly heard in area of 1st crankshaft main bearing. ^ Noise can no longer be heard when the poly-V belt is removed. ^ It is essential to compare the noise of the complaint vehicle! ^ Noise is irregular. Pulse-like crackling noise occurs at irregular intervals. ^ 20 pulses (ticking) which represent justifiable complaints. Cau...
Read more

YEOREO Workout Leggings Review | No Front Seam Straight Leggings

YEOREO Workout Leggings Review | No Front Seam Straight Leggings Women’s Leggings Review YEOREO Workout Leggings Review The YEOREO Workout Leggings Womens No Front Seam Straight Leggings are designed for shoppers who want a smoother, more flattering fit than traditional front-seam leggings, while still getting a high waist, soft fabric, and a silhouette that works beyond the gym. The standout feature is the combination of no front seam , straight-leg styling , and four inseam choices: 29" , 31.5" , 33" , and 35" . ([yeoreo.com](https://www.yeoreo.com/products/yeoreo-eddiy-29-straight-leggings?utm_source=openai)) YEOREO’s official product pages describe the Eddiy line as high-waist straight-leg leggings with a V-back contouring detail, an ultra-soft sweat-wicking feel, and an `80% nylon / 20% sp...
Post a Comment
Read more