Skip to main content

Buying a used Volkswagen Polo

 


 


Buying a used Volkswagen Polo

 


 


 


In Brief


Volkswagen waltzed into India in 2007 but only really took the market seriously with their first major offering for India – the Polo, in 2009. With that, a 200,000 units/annum factory was set up but the company is yet to realize even half its manufacturing potential. When it comes to the Polo, it took off well as a lot of hype was created around the brand, but soon enough, the popularity of the Polo reduced. The Polo is expensive to buy as a new car and doesn’t offer equivalent bang for buck. It is well built though, rides well and is a good handler, comes in a wide variety of variants and has an attractive design.


 


On the road


Of the several variants a Polo comes in, that includes a petrol and diesel GT variant and a Cross Polo, the stock variants are the ones that are available in the pre-owned car market. The rest are relatively new offerings and were sold few and far between. The petrol and diesel mills on offer were 3-cylinder 1.2-litre engines with about 75PS power. Neither engine did justice to the fantastic chassis the Polo possesses. A new 1.5-litre diesel engine was introduced with the facelift a few months ago and finally gives the Polo the right amount of power. In the pre-owned car segment though, you will have to make to with the underpowered engines. What works for the Polo though is the good ride and handling balance and stability at high speeds. 


 


Moving in


For the price Volkswagen charged for a new Polo, you just didn’t get enough kit in comparison to the competition like the i20. Space on the inside, especially at the rear is a bit less. It has good amounts of boot space at 280 litres and with the rear seat folding almost flat, a lot of space is liberated. But the quality of materials and fit and finish is rather impressive for a car of this class. What affected Volkswagen were low levels of localization. This made it pricing the Polo competitively very tough. 


 


Efficiency


The Polo wasn’t as efficient as other cars in its segment, mainly due to a higher kerb weight. The petrol returns an ARAI certified figure of 17.2kmpl and the diesel clocks 22.07kmpl. These figures though are under ideal test conditions and real world efficiency should be in the range of 13kmpl for the petrol and about 17-18kmpl for the diesel.


 


Buying used


Being a good driver’s car, besides the engines of course, most Polo owners drive it with a bit less restraint than most other hatchbacks and that results in higher wear and tear of parts like tyres, suspension and brakes. So first thing you do while inspecting a Polo is check for tyre wear, brake feel and stopping power and lastly any noises from the suspension. Expect a wear distance of about 30,000km for the brake pads and suspension linkage. Tyre wear is easy to spot with the help of a coin test. The depth of the grooves should be more than 5mm and uniform for all tyres. The diesel Polo is prone to sump damage as it is low set. The longish front end bottoms out when the suspension compresses over large potholes at medium to high speeds so check for sump damage. Hard wearing interior is a boon for a pre-owned car so that’s one aspect you will not be disappointed with.


 


Money Wise


The Polo petrol will cost about Rs 3 lakh for a 2009 model. Add in the range of Rs 25,000 for a example that’s a year younger. The diesel Polo will cost you around Rs 3.7 lakh for a good example. Add Rs 30-35,000 more for a 2010 model and so on. These prices are for a top end Highline variant. As you go a variant lower, shave off another Rs 30,000 for a Comfortline and Rs 60-70,000 for a Trendline Polo.


 

Comments

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138, Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...