Skip to main content

2010 Cadillac Truck SRX AWD V6-3.0L Page 898

2010 Cadillac Truck SRX AWD V6-3.0L Page 898



Control Module References (See: Testing and Inspection/Programming and Relearning)for scan tool information



Circuit/System Verification



Ignition ON, observe the scan tool EBCM Wheel Speed Sensor parameters. The reading should be the same speed on all sensors when driving in a



straight line at a speed greater than 20 km/h (13 MPH).



Circuit/System Testing



1. Ignition ON, verify that DTC C0035, C0040, C0045, or C0050 is not present in the EBCM.



瀚慖f any listed DTC is present, refer to DTC C0035, C0040, C0045, or C0050 (See: C Code Charts/C0035) to diagnose that DTC prior to



this diagnostic.



2. Replace the K17 Electronic Brake Control Module (EBCM) and verify the DTC does not reset.



瀚慖f the DTC resets, replace the module that set the DTC.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



Control Module References (See: Testing and Inspection/Programming and Relearning)for module replacement, setup and programming



C1226



DTC C1207-C1210, C1221-C1228, or C1232-C1235



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions)provides an overview of each diagnostic category.



DTC Descriptor



DTC C1207 00



- Left Front Wheel Speed Sensor Circuit High Input Malfunction



DTC C1208 00



- Right Front Wheel Speed Sensor Circuit High Input Malfunction



DTC C1209 00



- Left Rear Wheel Speed Sensor Circuit High Input Malfunction



DTC C1210 00



- Right Rear Wheel Speed Sensor Circuit High Input Malfunction



DTC C1221 00



- Left Front Wheel Speed Sensor Circuit Malfunction



DTC C1222 00



- Right Front Wheel Speed Sensor Circuit Malfunction



DTC C1223 00



- Left Rear Wheel Speed Sensor Circuit Malfunction



DTC C1224 00



- Right Rear Wheel Speed Sensor Circuit Malfunction



DTC C1225 00



- Left Front Wheel Speed Sensor Circuit Performance Malfunction



DTC C1226 00



- Right Front Wheel Speed Sensor Circuit Performance Malfunction

Comments

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138, Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...