Mercedes Benz E 550 4MATIC Sedan Technical Service Bulletin # LI58-40

Mercedes Benz E 550 4MATIC Sedan Technical Service Bulletin # LI58-40_P-048513 Date: 091124

Mercedes Benz E 550 4MATIC Sedan Technical Service Bulletin # LI58-40_P-048513 Date: 091124
Computers/Control - XD/DAS Add-Ons Software Update
DAS/XD ADD-ON 2009-10-29-1294 FOR PASSENGER CARS
Topic number LI58.40-P-048513
Version 1
Design group 58.40 Workshop equipment/MB testers
Date 11-24-2009
Validity DVD version 10/2009
Reason for change
Reason for block
Complaint:
AAC
Model series: 221, 216
Fault code 963C is set and AC OFF cannot be activated
ISM
Model series: 164, 212, 216, 221, 251
Control unit programming for hardware object number 0054461710 reports:
"The following control unit software versions
are available for control unit programming: 0114489610, 0124484610." After control unit programming, the control unit cannot be started up.
ETC
Model series: 204
Control unit programming for software object number 0024484710 reports: "No newer control unit software found".
2010 Mercedes Benz E 550 4MATIC Sedan (212.090) V8-5.5L (273.970) Page 273
DTR
Model series: 216
Control unit programming for software object number 2164420400 reports: "No newer control unit software found".
ME 2.7.2
Model series: 230
Control unit programming for various hardware object numbers reports: "No newer control unit software found".
CDI6
Model series: 164
Control unit programming for hardware object number 6429010400 reports: "No newer control unit software found".
CDI6
Model series: 164, 251
Control unit programming for software object numbers 642 902 69 00, 642 903 53 00 and 642 903 54 00 reports: "No newer control unit software
found".
Front SAM
Model series: 164, 251
Control unit programming for software object numbers 164 442 17 00 and 164 442 33 00 reports: "No newer control unit software found".
ESP
Model series: 207
Control unit programming for software object numbers 212 442 19 53 and 212 902 04 00 reports: "No newer control unit software found".
ICM
Model series: 212
Control unit programming for various hardware object numbers reports: "No newer control unit software found".
TGW
Model series: 204
Control unit programming for hardware object numbers 204 870 15 89, 204 870 17 90, 204 870 70 89 and 204 870 79 90 reports: "The following
control unit software versions are available for control unit programming: 204 902 15 01 and 204 902 30 01" After control unit programming, the
control unit cannot be started up.
Cause:
For all complaints: XD and DAS diagnostic data.
Remedy:
DAS/XD add-on 2009-10-29-1294 for passenger cars:
This add-on can be installed over DAS/XD version 10/2009.
This add-on does not supersede any other add-ons and must be additionally installed.
2010 Mercedes Benz E 550 4MATIC Sedan (212.090) V8-5.5L (273.970) Page 274
Symptoms
Control unit/fault code
2010 Mercedes Benz E 550 4MATIC Sedan (212.090) V8-5.5L (273.970) Page 275
Validity

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V86.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: A80 (Intelligent servo module for DIRECT SELECT) Affected functions: Drive position selection Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:270641Possible cause and remedy Internal fault in control unit Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**: - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**: - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**: - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**: - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138， Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...

Mercedes Benz

Search This Blog