2010 Cadillac Truck SRX FWD V6-3.0L Page 1929

2010 Cadillac Truck SRX FWD V6-3.0L Page 1929

* The ECM has commanded the Camshaft Position Actuator Solenoid Valve ON and OFF at least once during the ignition cycle.

* DTCs P0010, P0013, P0020, P0023, P2088, P2089, P2090, P2091, P2092, P2093, P2094, and P2095 run continuously once the above

conditions are met for greater than 1 second.

Conditions for Setting the DTC

P0010, P0013, P0020, P0023

The ECM detects an open in the Camshaft Position Actuator Solenoid Valve circuits for greater than 1 s or a cumulative of 5 s, when the solenoid

valve is commanded OFF.

P2088, P2090, P2092, P2094

The ECM detects a short to ground in the Camshaft Position Actuator Solenoid Valve circuits for greater than 1 s or a cumulative of 5 s, when the

solenoid valve is commanded OFF.

P2089, P2091, P2093, P2095

The ECM detects a short to voltage in the Camshaft Position Actuator Solenoid Valve circuits for greater than 1 s or a cumulative of 5 s, when the

solenoid valve is commanded ON.

Action Taken When the DTC Sets

DTCs P0010, P0013, P0020, P0023, P2088, P2089, P2090, P2091, P2092, P2093, P2094, and P2095 are type B DTCs.

Conditions for Clearing the DTC

DTCs P0010, P0013, P0020, P0023, P2088, P2089, P2090, P2091, P2092, P2093, P2094, and P2095 are type B DTCs.

Diagnostic Aids

If the condition is intermittent, move the related harnesses and connectors, with the engine operating, while monitoring the scan too circuit status

parameters for the component. The circuit status parameters change from OK or Not Run to Fault if there is a condition with the circuit or a

connection.

Reference Information

Schematic Reference

Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Camshaft Actuator System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Camshaft

Actuator System)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. With the engine at normal operating temperature, raise the engine speed to 2,000 RPM for 10 s. DTCs P0010, P0013, P0020, P0023, P2088,

P2089, P2090, P2091, P2092, P2093, P2094, or P2095 should not set.