Skip to main content

Disclaimer2010 Cadillac Truck Escalade RWD V8-6.2L Technical Service Bulletin # 06-08-44-034E Date: 110211

Disclaimer2010 Cadillac Truck Escalade RWD V8-6.2L Technical Service Bulletin # 06-08-44-034E Date: 110211



Navigation Radio - Various Noises Explained



INFORMATION



Bulletin No.: 06-08-44-034E



Date: February 11, 2011



Subject: Information on Noise Sources from Navigation Radio - CD/DVD Disc Accessing Noise from Radio Fan, for Cooling, Disc Accessing



Noise for Navigation Operation or NAV Traffic Information



Models:



2008-2011 Buick Enclave



2007-2009 Cadillac SRX



2007-2011 Cadillac DTS, Escalade, Escalade ESV, Escalade EXT



2007-2011 Chevrolet Avalanche, Silverado, Suburban, Tahoe



2009-2011 Chevrolet Traverse



2007-2011 GMC Acadia, Sierra, Yukon, Yukon Denali, Yukon XL, Yukon Denali XL



2010 Cadillac Truck Escalade RWD V8-6.2L Page 206



2007-2009 HUMMER H2



2007-2010 Saturn OUTLOOK



Supercede:



This bulletin is being revised to add the 2011 model year. Please discard Corporate Bulletin Number 06-08-44-034D (Section 08 - Body and



Accessories).



Some customers may comment that there are unusual fan type noises coming from the navigation radio. Additionally, the customer may comment



on radio noise coming from the CD/DVD or MAP disc mechanisms when CDs/DVDs or MAP discs are present in the CD mechanisms. Some



customers have mentioned that radio noise is present when the customer enters the vehicle or that the noise continues after they shut the vehicle off



and open the door to leave the vehicle. This noise has been described as a fan sound or hearing a disc spinning.



Source of fan sound - It is normal for the radio fan to run when the vehicle is turned on and for up to three minutes after the vehicle has been



turned off and the driver's door has been opened or closed.



Disc spinning sound - This is a normal operational sound. This is caused by the map disc spinning behind the tilt screen. It is a normal operation



after the RKE is used to unlock the vehicle or when the driver's door has been opened. This noise will also be heard during vehicle operation and up



to three minutes after the vehicle has been turned off and driver's door has been opened and closed.



MAP Disc Accessing "ZIP" sound - As the Navigation Radio accesses the MAP Disc, the customer may describe frequent "zip" type noises. This



noise is caused by the CD Read Lens moving across the disc to access needed data for proper MAP display. To determine if the source of the noise



is from accessing the MAP Disc, remove the MAP Disc to determine if the noise continues. With the addition of the Real Time NAV Traffic



Feature, the MAP CD may be accessed to a greater extent thus resulting in additional MAP Drive noise.



Inform the customer about these noises. If the customer believes the noise is not normal, compare the condition to a like vehicle with identical



settings to determine if there is a noticeable difference.



Do not replace the radio as the described conditions are normal operating characteristics.

Comments

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138, Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...