Saturday, July 31, 2021

2010 Cadillac Truck SRX AWD V6-3.0L Page 2113

2010 Cadillac Truck SRX AWD V6-3.0L Page 2113



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning)



Circuit/System Verification



1. Ensure the transmission fluid temperature is between 50-80掳C (122-176掳F).



2. Operate the vehicle in 2nd gear long enough to ensure at least a 3掳C (5掳F) rise in transmission fluid temperature, then operate the vehicle in



Park for 5 s.



3. Observe the scan tool Brake Band Pressure Control Solenoid Valve Current parameter. The reading should be between 0.1-1.1 A.



Circuit/System Testing



Command the Shift Brake Pressure Control Solenoid Valve with a scan tool. The value should change from 0.0-1.0 A.



If the value does not change, turn ignition OFF, remove the K71 Transmission Control Module. Connect a test lamp between the low reference



circuit terminal 16 X2 at the K71 Transmission Control Module and the voltage supply component circuit terminal 21 X2 at the K71 Transmission



Control Module. Command the Shift Brake Pressure Control Solenoid Valve with a scan tool. The test lamp has to illuminate brighter with



increasing current.



If the test lamp always illuminates or always does not illuminate, replace the K71 Transmission Control Module.



Component Testing



Static Test



1. Ignition OFF, remove the K71 Transmission Control Module.



2. Test for 5-5.6 ohm at 20掳C (68掳F) between the low reference circuit terminal 16 X2 and the voltage supply circuit terminal 21 X2.



瀚慖f less than the specified range, test the wiring harness for internal short. If the circuit test normal, replace the Q27E Pressure Control



Solenoid Valve 5.



3. Test for infinite resistance between each terminal and the low reference circuit terminal 16 X2 and also to the voltage supply circuit terminal



21 X2.



瀚慖f less than the specified range, replace the wiring harness.



4. If all circuit test normal, perform the Control Solenoid Valve Inspection (M36 and MXE) (See: Transmission and Drivetrain/Automatic



Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/AF40-6 - Automatic Transmission).



瀚慖f the inspection tests normal, replace the control valve body.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Control valve body replacement-Refer to Control Valve Body Replacement (See: Transmission and Drivetrain/Automatic



Transmission/Transaxle/Valve Body/Service and Repair/AF40-6 - Automatic Transmission/Control Valve Body Replacement).



* TCM-Refer to Control Module References (See: Testing and Inspection/Programming and Relearning).



* Wiring harness-Refer to Automatic Transmission Wiring Harness Replacement (See: Transmission and Drivetrain/Automatic



Transmission/Transaxle/Wiring Harness/Service and Repair).



6T70/6T75 - Automatic Transmission



DTC P2728-P2730



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC P2728



- Clutch Pressure Control (PC) Solenoid 5 System Performance

No comments:

Post a Comment