2010 Cadillac Truck SRX FWD V6-3.0L Page 532

2010 Cadillac Truck SRX FWD V6-3.0L Page 532

Description and Operation

Heated/Vented Seat Description and Operation (See: Body and Frame/Seats/Seat Temperature Element/Description and Operation/Heated/Vented

Seat)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Testing

B2425 0B, B2425 0D, or B2425 0E

1. Ignition OFF, disconnect the X4 harness connector at the K40 seat memory control module.

2. Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal 5 and ground.

瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.

3. Ignition OFF, connect the X4 harness connector at the K40 seat memory control module and disconnect the harness connector at the E14A

seat back heating element.

Note: Element resistance must be measured twice to ensure that all failure conditions are simulated. First with the seat unoccupied, then with

the seat occupied.

4. Test for 0.5 - 5 Ohms between terminal A and terminal B.

瀚慖f not within the specified range, replace the E14A seat back heating element.

5. Connect the harness connector at the E14A seat back heating element and disconnect the X3 harness connector at the K40 seat memory

control module.

Note: Element resistance must be measured twice to ensure that all failure conditions are simulated. First with the seat unoccupied, then with

the seat occupied.

6. Test for 1 - 7 Ohms between control circuit terminal 11 and control circuit terminal 6.

瀚慖f less than the specified range, test for a short between the control circuits. If the circuits test normal, replace the E14B seat cushion

heating element.

瀚慖f greater than the specified range, test the control circuits for an open/high resistance. If the circuits test normal, replace the E14B seat

cushion heating element.

7. If all circuits test normal, replace the K40 seat memory control module.

B2430 0B, B2430 0D, or B2430 0E

1. Ignition OFF, disconnect the X4 harness connector at the K40 seat memory control module.

2. Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal 5 and ground.

瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.

3. Ignition OFF, connect the X4 harness connector at the K40 seat memory control module and disconnect the harness connector at the E14C

seat back heating element.

Note: Element resistance must be measured twice to ensure that all failure conditions are simulated. First with the seat unoccupied, then with

the seat occupied.

4. Test for 0.5 - 5 Ohms between terminal A and terminal B.

瀚慖f not within the specified range, replace the E14C seat back heating element.

5. Connect the harness connector at the E14C seat back heating element and disconnect the X3 harness connector at the K40 seat memory