2010 Cadillac Truck SRX AWD V6-3.0L Page 1646

2010 Cadillac Truck SRX AWD V6-3.0L Page 1646

DTCs P0667, P0668, and P0669 are Type B DTCs.

Diagnostic Aids

The transmission control module (TCM) temperature sensor is located inside of the control solenoid valve assembly and its output should resemble

that of the transmission fluid temperature (TFT) sensor output.

Reference Information

Connector End View Reference

* Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

* Inline Harness Connector End Views (See: Diagrams/Connector Views/Multiple Junction Connector/Connector End Views By Number)

Description and Operation

Electronic Component Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and Operation/6T70/6T75 -

Automatic Transmission/Electronic Component Description) for control solenoid valve assembly

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Engine idling at normal operating temperature, verify the scan tool TCM Temperature parameter is between -247 and +247掳C (-412 and

+477掳F).

瀚慖f not within the specified range, replace the control solenoid valve assembly.

2. Operate the vehicle at 64 km/h (40 mph) for 10 minutes. Monitor the TCM Temperature, TCM Power-up Temperature, and the Trans. Fluid

Temp. parameters with a scan tool. The TCM Temperature and the Trans. Fluid Temp. parameters should be within 20掳C (36掳F) of each

other, and the TCM Temperature and TCM Power-up Temperature parameters should be within 10掳C (18掳F) of each other.

瀚慖f the TCM Temperature and TCM Power-up Temperature parameters are not within 10掳C (18掳F), or the TCM Temperature and Trans.

Fluid Temp. parameters are not within 20掳C (36掳F), then replace the control solenoid valve assembly.

3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Repair Instructions

Important:

* Perform the Service Fast Learn Adapts (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and

Inspection/Programming and Relearning) following all transmission related repairs.

* Before replacing the TCM, perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See:

Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component Tests and General

Diagnostics/6T70/6T75 - Automatic Transmission/Control Solenoid Valve and Transmission Control Module Assembly Inspection).

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning) for control solenoid valve assembly replacement, setup,