2010 Cadillac Truck SRX AWD V6-3.0L Page 319

-

2010 Cadillac Truck SRX AWD V6-3.0L Page 319



Relay Test



1. Ignition OFF, disconnect the KR5 rear defogger relay.



2. Test for 60-180 ohm between terminals 85 and 86.



瀚慖f not within the specified range, replace the KR5 rear defogger relay.



3. Test for infinite resistance between the following terminals:



* 30 and 86



* 30 and 87



* 30 and 85



* 85 and 87



瀚慖f not the specified value, replace the KR5 rear defogger relay.



4. Install a 25A fused jumper wire between relay terminal 86 and 12V. Install a jumper wire between relay terminal 85 and ground. Test for less



than 2 ohm between terminals 30 and 87.



瀚慖f greater than the specified range, replace the KR5 rear defogger relay.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Relay Replacement (Attached to Wire Harness) (See: Power and Ground Distribution/Power Distribution Relay/Service and Repair/Relay



Replacement (Attached to Wire Harness))Relay Replacement (Within an Electrical Center) (See: Power and Ground Distribution/Power



Distribution Relay/Service and Repair/Relay Replacement (Within an Electrical Center))



* Control Module References (See: Testing and Inspection/Programming and Relearning) for HVAC control module replacement, setup and



programming



B291A



DTC B291A



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptor



DTC B291A 39



- Content Theft Deterrent Assembly Internal Malfunction



Circuit/System Description



The content theft deterrent intrusion/inclination sensor performers an internal self-check to determine it is functioning properly.



Conditions for Running the DTC



* The ignition is OFF.



* The vehicle is in Park.



Conditions for Setting the DTC



The body control module (BCM) detects an internal failure within the content theft deterrent intrusion/inclination sensor.



Action Taken When the DTC Sets



The intrusion and inclination output is disabled.



Conditions for Clearing the DTC



* A current DTC is cleared when the conditions for setting the DTC are no longer present.

Comments

Post a Comment

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

-
P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...
Read more

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

-
Image
  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...
Read more

The BMW M5 Sedan & M5 Touring with BMW M Performance Parts.

-
Image
 BMW (Benz-Wesbach) is a well-known and respected luxury brand in the European automotive market, particularly for sports cars like the M5. However, unlike some other car manufacturers, BMW has not primarily focused on its formula racing or sport engineering heritage. Instead, the BMW M series has been a strong seller due to their sportiness, reliability, and aesthetic appeal. If you're referring to BMW's M5 sedan **and touring variant** with performance parts, here are some key points to consider: 1. **Performance Improvement**:     - BMW’s sports cars, including the M5 models, have improved over previous iterations. The 3.0 liter straight-6 power plant in the M5 has seen improvements like a new torque vectoring system and increased engine robustness. These upgrades can enhance acceleration and cornering stability compared to older versions of the car. 2. **Eco-Friendly Parts**:    - BMW is known for introducing eco-friendly components, particularly in veh...
Read more