Thursday, October 1, 2020

2010 Cadillac Truck SRX AWD V6-3.0L Page 581

2010 Cadillac Truck SRX AWD V6-3.0L Page 581



* When the fault is no longer present, the DTC will be a history DTC.



* A history DTC will clear after 50 ignition cycles.



Reference Information



Schematic Reference



Headlights/Daytime Running Lights (DRL) Schematics (See: Diagrams/Electrical Diagrams/Lighting and Horns/System



Diagram/Headlights/Daytime Running Lights (DRL) Schematics)



Connector End View Reference



Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)



Description and Operation



Exterior Lighting Systems Description and Operation (See: Lighting and Horns/Description and Operation/Exterior Lighting Systems)



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit



Testing/Circuit Testing)



* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic



Procedures/Connector Repairs/Connector Repairs)



* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General



Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)



* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring



Repairs/Wiring Repairs)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Circuit/System Verification



Ignition ON, command the Left Dedicated Daytime Running Lamp and the Right Dedicated Daytime Running Lamp ON and OFF with a scan tool.



The E4C daytime running lamp - left and the E4D daytime running lamp - right should turn ON and OFF while changing between the commanded



states.



Circuit/System Testing



1. Ignition OFF, disconnect the X1 harness connector K9 BCM.



2. Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal 3 and ground.



瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.



3. Ignition OFF, connect the X1 harness connector K9 BCM



4. Ignition OFF, disconnect the inline harness connector listed below:



* E4C daytime running lamp - left X111 inline harness connector



* E4D daytime running lamp - right X116 inline harness connector



5. Connect a test lamp between the control circuit terminal G and ground.



6. Command the appropriate Dedicated Daytime Running Lamp ON and OFF with a scan tool. The test lamp should turn ON and OFF when



changing between the commanded states.



瀚慖f the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the K9 BCM.



瀚慖f the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuits test normal, replace



the K9 BCM.



7. If all circuits test normal, replace the daytime running lamp bulb.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Daytime Running Lamp Bulb Replacement (TT6,TT7,TT8 Passenger Side Headlamp) (See: Lighting and Horns/Daytime Running



Lamp/Service and Repair/Daytime Running Lamp Bulb Replacement (TT6,TT7,TT8 Passenger Side Headlamp))Daytime Running Lamp



Bulb Replacement (T84, T85 Passenger Side Headlamp) (See: Lighting and Horns/Daytime Running Lamp/Service and Repair/Daytime



Running Lamp Bulb Replacement (T84, T85 Passenger Side Headlamp))Daytime Running Lamp Bulb Replacement (T84, T85 Driver Side



Headlamp) (See: Lighting and Horns/Daytime Running Lamp/Service and Repair/Daytime Running Lamp Bulb Replacement (T84, T85



Driver Side Headlamp))Daytime Running Lamp Bulb Replacement (TT6,TT7,TT8 Driver Side Headlamp) (See: Lighting and



Horns/Daytime Running Lamp/Service and Repair/Daytime Running Lamp Bulb Replacement (TT6,TT7,TT8 Driver Side Headlamp))



* Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, setup, and programming

No comments:

Post a Comment