2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1759
* This DTC runs continuously when the above conditions are met.
P0113
* DTCs P0101, P0102, P0103, P0116, P0117, P0118, P0125, P0128, P0722, P0723 are not set.
* The engine is running for greater than 10 s.
* The ECT is warmer than -40掳C (-40掳F).
* The MAF Sensor signal is equal to or greater than 512 g/s.
* This DTC runs continuously when the above conditions are met.
Conditions for Setting the DTC
P0112
The ECM detects that the IAT sensor signal is warmer than 149掳C (300掳F) for greater than 5 s.
P0113
The ECM detects that the IAT sensor signal is colder than -39掳C (-38掳F) for greater than 5 s.
Action Taken When the DTC Sets
DTCs P0112 and P0113 are Type B DTCs.
Conditions for Clearing the MIL/DTC
DTCs P0112 and P0113 are Type B DTCs.
Diagnostic Aids
* With the ignition ON, the engine OFF, if the engine is cold, a properly functioning IAT sensor will gradually increase the scan tool IAT
Sensor parameter. This is due to the heat that is generated by the mass air flow (MAF) sensor heating elements.
* Depending on the ambient temperature, an IAT sensor signal circuit or low reference circuit that is shorted to the MAF sensor signal circuit
can cause a DTC P0113 to set. This condition causes a rapid fluctuation in the IAT Sensor parameter.
* An IAT sensor signal circuit that is shorted to the MAF sensor ignition circuit can cause a DTC P0113 to set.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
1. Engine idling, observe the scan tool IAT Sensor parameter. The reading should be between -38 to +149掳C (-36 to +300F) depending on the
current ambient temperature and the vehicle operating conditions.
2. Operate the vehicle within the Conditions for Running the DTC to verify that the DTC does not reset. You may also operate the vehicle
within the conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Saturday, October 31, 2020
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1759
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment